Siemens SCALANCE XR-300WG Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 100

background image

Connecting up

6

6.1

Safety when connecting up

Safety notices

When connecting up the device, keep to the safety notices listed below.

If using power sources according to NEC Class 2 or LPS, please note the following information:

WARNING

The equipment is designed for operation with Safety Extra-Low Voltage (SELV) by a Limited
Power Source (LPS).

This means that only SELV / LPS complying with IEC 60950-1 / EN 60950-1 / VDE 0805-1 must
be connected to the power supply terminals, or the power supply unit for the equipment power
supply must comply with NEC Class 2, as described by the National Electrical Code (r) (ANSI /
NFPA 70).

If the equipment is connected to a redundant power supply (two separate power supplies),
both must meet these requirements.

WARNING

Do not remove or replace while circuit is live when a flammable or combustible atmosphere is
present.

Note
No light power measurement (PROFINET diagnostics)

The devices do not support diagnostics with light power measurement.

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD

Do not connect or disconnect cables to or from the device when a flammable or combustible
atmosphere is present.

SCALANCE XR-300WG
Operating Instructions, 03/2021, C79000-G8976-C454-07

49

«
...
47
48
49
50
51
...
»

Содержание SCALANCE XR-300WG





































































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE XR-300WG

DGS-1024D - Switch

Бренд: D-Link Страницы: 16

DGS-1016D - Switch

Бренд: D-Link Страницы: 44

DES-6000 Series

Бренд: D-Link Страницы: 3

DES-5024 - Switch

Бренд: D-Link Страницы: 2

DES-3828 - xStack Switch - Stackable

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 192

Бренд: D-Link Страницы: 9

Бренд: D-Link Страницы: 110

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 17

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 9

Бренд: D-Link Страницы: 4

DGS-105 - Switch

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 2

TECMA Silence Marine

Бренд: Thetford Marine Страницы: 9

Бренд: Cabletron Systems Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды