Siemens SCALANCE XR-300WG Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 100

background image

WARNING

When used in hazardous environments corresponding to Class I, Division 2 or Class I, Zone 2,
the device must be installed in a cabinet or a suitable enclosure.

Safety notices for use according to ATEX and IECEx
If you use the device under ATEX or IECEx conditions you must also keep to the following safety
notices in addition to the general safety notices for protection against explosion:

WARNING

The equipment shall only be used in an area of not more than pollution degree 2, as defined in
EN/IEC 60664-1.

WARNING

Requirements for the cabinet/enclosure

The equipment shall be installed in a suitable enclosure that provides a degree of protection not
less than IP54 in accordance with EN/IEC 60079-15.

WARNING

If the temperature of the cable or housing socket exceeds 70 °C or the branching point of
conductors exceeds 80 °C, special precautions must be taken. If the equipment is operated in
an air ambient in excess of 50 °C to 60 °C, only use cables with a permissible operating
temperature of at least 85 °C.

Safety notices when using according to FM
If you use the device under FM conditions you must also keep to the following safety notices in
addition to the general safety notices for protection against explosion:

WARNING

To fulfill the requirements of the FM approval rack mounting is only possible in a vent free, tool-
secured enclosure.

WARNING

Substitution of components may impair suitability for Division 2.

Installation
5.1 Safety notices for installation

SCALANCE XR-300WG

36

Operating Instructions, 03/2021, C79000-G8976-C454-07

«
...
34
35
36
37
38
...
»

Содержание SCALANCE XR-300WG





































































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE XR-300WG

Бренд: Talkswitch Страницы: 17

Бренд: Quick Страницы: 28

Бренд: 6TL Страницы: 25

VNLW-P-1001-MV-N-V

Бренд: Greengate Страницы: 2

HD Flash 4 KD-SW4x1

Бренд: Key Digital Страницы: 12

Бренд: REV Ritter Страницы: 15

Бренд: Sarowin Страницы: 9

Бренд: Comtrend Corporation Страницы: 2

Бренд: N-Tron Страницы: 169

Бренд: DLS Страницы: 226

Бренд: Gefen Страницы: 14

Бренд: hager Страницы: 2

Бренд: HIKVISION Страницы: 25

IES2100SL Series

Бренд: 3onedata Страницы: 3

AVlink VAX-8404F

Бренд: C&C TECHNIC Страницы: 2

Бренд: Led Control Страницы: 22

Бренд: CityGrow Systems Страницы: 21

Бренд: Gefen Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды