Siemens SAB 80515 Series Скачать руководство пользователя страница 238 | Manualshive

Страница: 238 / 270

Siemens SAB 80515 Series Скачать руководство пользователя страница 238

Device Specifications

Semiconductor Group

238

Serial Port

The serial port of the SAB 80C515 enables full duplex communication between microcontrol-
lers or between microcontroller and peripheral devices.
The serial port can operate in 4 modes:

Mode 0: Shift register mode. Serial data enters and exits through R

×

D. T

×

D outputs the

shift clock. 8-bits are transmitted/received: 8 data bits (LSB first).
The baud rate is fixed at 1/12 of the oscillator frequency.

Mode 1: 10-bits are transmitted (through R

×

D) or received (through T

×

D): a start bit (0),

8 data bits (LSB first), and a stop bit (1). The baud rate is variable.

Mode 2: 11-bits are transmitted (through R

×

D) or received (through T

×

D): a start bit (0),

8 data bits (LSB first), a programmable 9th data bit, and a stop bit (1).
The baud rate is programmable to either 1/32 or 1/64 of the oscillator frequency.

Mode 3: 11-bits are transmitted (through T

×

D) or received (through R

×

D): a start bit (0),

8 data bits (LSB first), a programmable 9th data bit, and a stop bit (1). Mode 3
is identical to mode 2 except for the baud rate. The baud rate in mode 3 is variable.

The variable baud rates in modes 1 and 3 can be generated by timer 1 or an internal
baud rate generator.

A/D Converter

The 8-bit A/D converter of the SAB 80C515 has eight multiplexed analog inputs (Port 6) and
uses the successive approximation method.
There are three characteristic time frames in a conversion cycle (see A/D converter
characteristics): the conversion time

t

C

, which is the time required for one conversion; the

sample time

t

S

which is included in the conversion time and is measured from the start of the

conversion; the load time

t

L

, which in turn is part of the sample time and also is measured from

the conversion start.
Within the load time

t

L

, the analog input capacitance

C

I

must be loaded to the analog inpult

voltage level. For the rest of the sample time

t

S

, after the load time has passed, the selected

analog input must be held constant. During the rest of the conversion time

t

C

the conversion

itself is actually performed. Conversion can be programmed to be single or continuous; at the
end of a conversion an interrupt can be generated.

A unique feature is the capability of internal reference voltage programming. The internal
reference voltages

V

I ntAREF

and

V

I ntAGND

for the A/D converter both are programmable to one

of 16 steps with respect to the external reference voltages. This feature permits a conversion
with a smaller internal reference voltage range to gain a higher resolution.
In addition, the internal reference voltages can easily be adapted by software to the desired
analog input voltage range.

Figure 4 shows a block diagram of the A/D converter.

*

«
...
236
237
238
239
240
...
»

Содержание SAB 80515 Series















































































































































































































































































Отзывы:

Нет отзывов