manualshive.com logo in svg

Siemens SAB 80515 Series, Руководство пользователя, Страница: 117 / 270

Поделиться
Скачать
Siemens SAB 80515 Series Скачать руководство пользователя страница 117

Semiconductor Group

117

Interrupt System

The serial port interrupt is generated by a logical OR of flag RI and Tl in SFR SCON (see
figure 7-7). Neither of these flags is cleared by hardware when the service  routine is vectored too.
In fact, the service routine will normally have to determine whether it was the receive interrupt flag
or the transmission interrupt flag that generated the interrupt, and the bit will have to be cleared by
software.

The timer 2 interrupt is generated by the logical OR of bit TF2 in register T2CON and bit EXF2 in
register IRCON. Figures 8-5 and 8-6 show SFR’s T2CON and IRCON. Neither of these flags is
cleared by hardware when the service routine is vectored to. In fact, the service routine may have
to determine whether it was TF2 or EXF2 that generated the interrupt, and the bit will have to be
cleared by software.

Figure 8-4
Special Function Register TCON (Address 88H)  

     

The A/D converter interrupt is generated by IADC in register IRCON (see figure 8-6). lt is set
some cycles before the result is available. That is, if an interrupt is generated, in any case the
converted result in ADDAT is valid on the first instruction of the interrupt service routine (with
respect to the minimal interrupt response time). lf continuous conversions are established, IADC is
set once during each conversion. lf an A/D converter interrupt is generated, flag IADC will have to
be cleared by software.

Bit

Function

IT0

Interrupt 0 type control bit. Set/cleared by software to specify falling edge/low-
level triggered external interrupts.

IE0

Interrupt 0 edge flag. Set by hardware when external interrupt edge is detected. 
Cleared when interrupt processed.

IT1

Interrupt 1 type control bit. Set/cleared by software to specify falling edge/low-
level triggered external interrupts.

IE1

Interrupt 1 edge flag. Set by hardware when external interrupt edge is detected. 
Cleared when interrupt processed.

TF0

Timer 0 overflow flag. Set by hardware on timer/counter overflow. Cleared by 
hardware when processor vectors to interrupt routine.

TF1

Timer 1 overflow flag. Set by hardware on timer/counter overflow. Cleared by 
hardware when processor vectors to interrupt routine.

8FH

8EH

C5H

8CH

8BH

8AH

89H

88H

TF1

TR1

TF0

TR0

IE1

IT1

IE0

IT0

88H

TCON

These bits are not used for interrupt control.

*

Содержание SAB 80515 Series















































































































































































































































































Отзывы:

Нет отзывов