Siemens POL955, Инструкция по установке, использованию и техническому обслуживанию

Страница: 75 / 96

75
TUTORBIT
COSMOGAS
6 - USE
Maximum voltage
Voltage for defining the “Maximum temperature” of the heat generator
Installer
1.5...10
10 V
Minimum voltage
Voltage for defining the “Minimum temperature” of the heat generator
Installer
1.5...10
1.5 V
Stand-by voltage
Voltage at which the heat generator goes in Stand-by
Factory
0...3
0.5 V
DHW adjustment curve
Adjustment curve for when the generators are set as “DHW”
Installer
Maximum temperature
Maximum temperature that can be reached by the generator when t
he signal is “Maximum voltage”
Installer
20...90
75 °C
Minimum temperature
Minimum temperature that can be reached by the generator when the signal is “Minimum voltage”
Installer
20...50
32 °C
Maximum voltage
Voltage for defining the “Maximum temperature” of the heat generator
Installer
1.5...10
10 V
Minimum voltage
Voltage for defining the “Minimum temperature” of the heat generator
Installer
1.5...10
1.5 V
Modbus adjustment curve
Adjustment curve not available for these models of temperature controller
. Do not change.
Installer
Maximum temperature
N/A
Installer
20...90
75 °C
Minimum temperature
N/A
Installer
20...50
32 °C
Maximum voltage
N/A
Installer
1.5...10
10 V
Minimum voltage
N/A
Installer
1.5...10
0.5 V
Stand-by voltage
N/A
Factory
0...3
0.5 V
Save & Reset
Each time this menu is changed, you need to save and reset in order to load the changes in the temperature controller
Installer
Zones
Setting menus of the heating circuits
Installer
Zone 1 mode
“T
ype of heating circuit control:
“”FixSp-R
T”” = Fixed setpoint set in the “”Parameters>Zones>Heat Supply Setp” parameter
. Opening of the
corresponding R
T switches the heating of
f.
“”Outd Reset-R
T”” = Climatic adjustment with outdoor sensor
. The outdoor reset settings must be done in the
“”Parameters>Zones>Outdoor reset ”” menu. Opening of the corresponding R
T switches the heating of
f.
“”Outd Reset comp-R
T”” = Climatic adjustment with outdoor sensor
. The outdoor reset settings must be done
in the “”Parameters>Zones>Outdoor reset”” menu. Opening of the corresponding R
T generates a reduction in
the supply temperature corresponding to the value set in the “”Parameters>Zones>Night setback”” parameter
.
“”FxSp-Comp.R
T”” = Fixed setpoint set in the “”Parameters>Zones>Heat Supply Setp”” parameter
. Opening
of the corresponding R
T generates a reduction in the supply temperature corresponding to the value set in
“”Parameters>Zones>Night setback”” parameter
.
“”ModbusInput”” = Not applicable for this model of heat generator ““FixSp-RS”” = fixed setpoint with room sensor QMX3. ““Outd Reset-RS”” = Outdoor with room sensor QMX3.
Installer
FixSp-R
T;
Outd Reset-R
T;
Outd Reset comp-R
T;
FxSp-Comp. RT; ModbusInput; FixSp-RS; Outd Reset- RS;
FixSp-R
T
Zone 2 mode
The same as the “Zone 1 Mode” menu
Installer
as above
FixSp-R
T
Zone 3 mode
The same as the “Zone 1 Mode” menu
Installer
as above
FixSp-R
T
3 way valves
Menu to set common parameters of the heating circuits
Installer
Proportional band
PID proportional parameter that controls the opening and closure of the mixing valve
Installer
0...50
15 °C
Integral time
PID integral parameter that controls the opening and closure of the mixing valve
Installer
0...600
70 s
Pump delay
Delay of pump switch-on after receiving the start command
Installer
0...3600
1 s
Pump post-circulation
Pump post-circulation
Installer
0...3600
60 s
Continued on the next page