manualshive.com logo in svg

Siemens LITHOSTAR Multiline, Руководство по установке, Страница: 61 / 70

Поделиться
Скачать
Siemens LITHOSTAR Multiline Скачать руководство пользователя страница 61

Connections with POLYDOROS SX 65

4 - 19

Siemens AG

 

RXL2-120.812.01

Page 19 of 24

LITHOSTAR Multiline

Medical Solutions

Rev. 02

10.04

CS PS 24

System

 

Connections/harness locations in the generator cabinet (Part C)

4

•

Route the harnesses in the generator cabinet as shown in Fig. 13 above, and connect 
them in accordance with Table 10:

Generator power line connection 

Nominal Line Voltage: 400 V ± 10%

•

Secure the screw type terminals from the service packet to the conductors of the power 
cable. If the power cable diameter is small enough, turn the clamps 180° (both 
curvatures opposite to each other).

•

Apply end splices to the power cable.

•

Connect power leads L1, L2, L3, N, PE (connection 

/Fig. 13) to terminal strip K20.

•

Strain-relieve the power cable. Existing shielding should not be connected.

Generator - Periphery

Type of Cable

Function

Generator

ok

Power line cable
3/N/Gnd

System
power line connection

M16. K20 

Main distributor
L1, L2, L3, N, 

2 x 0.75 mm

2

Radiation protection

9)

M16.D160.X61 Door 

contact

2 x 0.75 mm

2

Radiation buzzer
Radiation display

9)

M16.D160.X61 X-ray 

display 

lamps

Tab. 10

9)

option

J

J

J

A

A

Содержание LITHOSTAR Multiline







































































Отзывы:

Нет отзывов