Siemens LITHOSTAR Multiline страница 24 Скачать руководство пользователя

Страница: 24 / 70

LITHOSTAR Multiline

RXL2-120.812.01

Page 2 of 20

Siemens AG

System

Rev. 02

10.04

CS PS 24

Medical Solutions

3 - 2

Connections with POLYDOROS LX 30

Fig. 2

Connections and cable locations in the A12
electronics cabinet

(green cable harnesses)

•

Fasten the 3 cable harnesses (green) with the cable clip on the rail that
is installed at the bottom of the electronics cabinet.

•

Secure the braided shield of the zipper hoses to the locations provided.

•

Route the cables in the A12 electronics cabinet as shown in the adjacent
Fig. 2 and connect them according to table 1 and 3.
The numbers or letters (e.g.

) are located in the cable lists on the

following pages.

•

Prior to routing the system cables, remove the EMC shielding plate at
N11 D11.

right

- cable harness,green, from control console

centre - cable harness,green, from unit (K3, K4....)

left

- cable harness, green, from unit (K8, K9....)

VIDEOMED

-DIM-

Mounting rail for cable harness

Cable harness, green, from the control console

Cable harness, green, from unit (K3, K4....)

Cable harness, green, from unit (K8, K9....)

3rd monitor on monitor trolley (optional)

Video cable 3rd monitor

Power Supply

M16

System

Controller

N11

Image Storage

A12

D21

X14

X15

L1.1

L1.2

Содержание LITHOSTAR Multiline







































































Результаты поиска

Содержание LITHOSTAR Multiline

Отзывы:

Похожие инструкции для LITHOSTAR Multiline

Бренды по названию

Популярные бренды

Siemens LITHOSTAR Multiline, Руководство по установке

Результаты поиска

Содержание LITHOSTAR Multiline

Отзывы:

Похожие инструкции для LITHOSTAR Multiline

Бренды по названию

Популярные бренды