Siemens LDS 6 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 102

Siemens LDS 6 Скачать руководство пользователя страница 61

Operation

4.3 Analyzer Functions

LDS 6
Operating Instructions, 01/2009, A5E00295894-05

61

Analog Test

The analog test can be used to parameter the analog output with a constant current of 0 - 24

mA for test purposes. The analog input permanently shows the input currents in mA.

81 Select Language

81 Select Language Ch1 NH

3

Español

Italiano

Français

Change requires restart

English

Deutsch

You can use this function to switch the analyzer to a different dialog language. The new

language will be effective in all screens only after having performed the following sequence:
1. Press the 'MEAS' key
2. Answer 'YES' in the following display
3. Restart the analyzer

82 Pressure Correction

Mode: Manual

82 Pressure Corr. Ch1 NH

3

1013 mbar

Manual Value:

700.0 - 1300 mbar

Limits:

[700.0]- 1300 mbar

Measuring Range:

Ana.Inp.2: 4-20mA(NAMUR)

You can use this function to select one of the following:
• Correction for pressure using an internal pressure sensor in the central unit;

• Correction for pressure using an external pressure sensor via analog input 2;

• Correction for pressure using a manual pressure value (example as shown on the adjacent

display).

The pressure values are entered as absolute pressure values. The selected measuring

range always corresponds to the analog input signal range of 4-20 mA. No other input

signals can be used. If the pressure sensor is configured according to the NAMUR standard,

the NAMUR mode should be selected for the analog input signal. In that case only input

signals within the range of 3.8 - 21.5 mA are accepted. If the NAMUR mode is not selected,

input signals within the range of 2 - 21 mA are accepted.
The limits normally mark the span in which pressure compensation is possible. If the

pressure signal exceeds the specified limits, this will be signalled as a maintenance request.
The parameters for the pressure correction in the corresponding factory function are

component-specific. Selection of the pressure mode in function 82 is channel-specific.
The pressure correction can be switched off.

83 Temperature Correction

Mode: Manual

83 Temp. Corr. Ch1 NH

3

300.0 °C

Manual Value:

0.00 - 1000 °C

Limits:

[0.00 ]- 400.0 °C

Measuring Range:

Ana.Inp.1: 4-20mA(NAMUR)

You can use this function to select one of the following:
• Correction for temperature using an external temperature sensor via analog

input 1 (example as shown on the adjacent display);

• Correction for temperature using a manual temperature value;

• Correction for temperature using the internally calculated process temperature.

This is only possible if the LDS 6 is set up to measure the temperature of the

measuring point.

«
...
59
60
61
62
63
...
»

Содержание LDS 6







































































































Отзывы:

Нет отзывов