Siemens LDS 6 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 102

Siemens LDS 6 Скачать руководство пользователя страница 16

Technical Information

2.2 Design

LDS 6

16

Operating Instructions, 01/2009, A5E00295894-05

Cross-duct sensors

Figure 2-4

Sensor CD 6, transmitter or receiver unit

● In-situ cross-duct sensors, configured as transmitter and receiver unit, connected via

sensor cable

●  Connection to the LDS 6 central unit by a so-called hybrid cable, max. length 700 m
●  Stainless steel, partially painted
●  IP65 degree of protection for sensor
●  Adjustable flanges with flange connection

DN 65/PN 6, ANSI 4"/150 lbs

● Optional flameproof window flanges with dimensions: DN 65/PN 6, DN 80/PN 16, ANSI

4"/150 lbs, other process interfaces available on request

● Purging facilities on the process and the sensor sides, configurable application with

purging gas connections for:
–  Instrument air
–  Purging air blower
–  Steam
–  Nitrogen
–  Process gases to which the pressure equipment directive cat. 2 does not apply

● In combination with high-pressure window flanges, purging with instrument air or nitrogen

is possible

● Fast connectors for cleaning the measurement openings and the sensor window

«
...
14
15
16
17
18
...
»

Содержание LDS 6







































































































Отзывы:

Нет отзывов