Siemens LDS 6 Скачать руководство пользователя страница 51

Страница: 51 / 102

Operation

4.3 Analyzer Functions

LDS 6
Operating Instructions, 01/2009, A5E00295894-05

4.3.3

Calibration

The LDS 6 is calibrated when delivered and does not normally require on site recalibration.

Please consult Siemens support if recalibration is needed.

CAUTION

Never use functions 20 and 21 without having contacted Siemens service staff first.

Inappropriate use of these functions may seriously affect the accuracy of the analyzer.

Access to the calibration functions requires access code 3.

20 Zero Calibration

Calibrate

Zero Calibration Active

20 Zero Calib. Ch1 NH

Act. Val. 0.12 mg/Nm

You can use this function to calibrate the zero of a measuring range. When zero

calibration is triggered the current measurement value is stored. This value will

thereafter always be subtracted from the measurement signal.

Only start the calibration, when the measured value is stable.
The status of the calibration will be shown at the bottom of the screen.

21 Span Calibration

Act. Val. 288.1 mg/Nm

Setpoint 293.0 mg/Nm

21 Span Calib. Ch1 NH

Calibrate

You can use this function to calibrate the span setpoint of a measuring range. This

display lists the setpoint and the current value.
The calibration is triggered by pressing the third soft key. The current value is then set

to coincide with the set point.

Содержание LDS 6







































































































Результаты поиска

Содержание LDS 6

Отзывы:

Siemens LDS 6, Руководство по эксплуатации, Страница: 51 / 102

Результаты поиска

Содержание LDS 6

Отзывы: