Siemens LDS 6 Скачать руководство пользователя страница 53

Страница: 53 / 102

Operation

4.3 Analyzer Functions

LDS 6
Operating Instructions, 01/2009, A5E00295894-05

51 Limits

Upper Limit[30.00] mg/Nm

51 Limits Ch1 NH

Lower Limit 0.00 mg/Nm

Limit Alarm On/Off

You can use this functions to set concentration limits. A limit alarm will be triggered when the

value of a component exceeds the permissible range set in this screen. The alarm can be turned

off here.
The limit alarm is displayed on the status line if this has been set up by function 53. The alarm is

also signalled by a relay if one has been assigned using function 71. The triggering of a limit

alarm is registered in the logbook (function 3).

52 Transmission

Set Nominal Value

52 Transmission Ch1 NH

Absolute 285.0 Units

Nominal 301.2 Units

Alarm Level[5 ] %

Transm. Alarm On/Off

Relative 84.93 %

You can use this function to set the transmission parameters. A transmission alarm is triggered

when the transmission is outside a permissible range. The lower alarm level of the transmission

for a channel is set as a percentage of the nominal transmission value, where the nominal value

is registered when the fourth soft key is pressed. The upper alarm level is set to a fixed value

and cannot be changed by the user.
The transmission alarm is displayed on the status line if this has been set up by function 53. The

alarm is also signalled by a relay if this has been set up by function 71. The triggering of a

transmission alarm is registered in the logbook

(function 3).

53 Status Messages

53 Status Messages Ch1 NH

[CTRL]

Display Func. Control

[LIM]

Display Limits

[STO]

Display Stored Value

Display Transm. Limits

[TR]

You can use this function to display - within the status line - up to four different statuses which

can be assumed by the analyzer.

Table 4- 7

Op. 3

Function

Status

STO: Stored Value

Analog output connected to memory (see also function 77).

LIM: Limit

Upward or downward violation of limit (see also function 51).

CTRL: Function Control

Start-up mode - Service mode.

TR: Transmission

Upward or downward violation of transmission limit (see also

function 52).

Содержание LDS 6







































































































Результаты поиска

Содержание LDS 6

Отзывы:

Siemens LDS 6, Руководство по эксплуатации, Страница: 53 / 102

Результаты поиска

Содержание LDS 6

Отзывы: