manualshive.com logo in svg

Siemens LDS 6, Руководство по эксплуатации, Страница: 38 / 102

Поделиться
Скачать
Siemens LDS 6 Скачать руководство пользователя страница 38

Installation Guidelines 

 

3.6 Installation of Flanges 

 

LDS 6 

38

 

Operating Instructions, 01/2009, A5E00295894-05 

Alignment procedure. 

2

1

4

2

3

 

Figure 3-7 

Usage of the items in the flange alignment kit 

1.

 

Light source 

2.

 

Alignment flanges 

3.

 

Aiming tool 

4.

 

Process flange to be aligned 

This is the alignment procedure 
1.

 

Weld the flange tubes loosely on each side of the wall. Do not weld them so hard that the 

angle of the tubes can not be adjusted with a hammer. 

2.

 

Mount the light source on one flange and the aiming tool on the other flange. 

3.

 

Turn on the light source. 

4.

 

Adjust the focus on the aiming tool until the light spot from the light source is sharp. 

5.

 

Adjust the angle of the process flange tube, using for instance a rubber hammer, until the 

light spot is centered on the cross hair on the aiming tool. 

6.

 

Weld the aligned flange tube permanently into this position. 

7.

 

Shift light source and aiming tool and repeat the procedure above for the opposite flange 

until the other tube also is permanently welded. 

 

 

 

Note 
It is important that the flanges are aligned from both sides. Therefore, remember to shift 

light source and aiming tool and repeat the procedure from the other side as well. It is 

also important that the sensor flanges are oriented in such a way that the spring loaded 

bolts are located in the lower section of the flange. 

 

Содержание LDS 6







































































































Отзывы:

Нет отзывов