Siemens KMS Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 89

background image

BA 9137 en 12/2015

Note

If the quality of the oil used does not meet the requirements of the separately supplied BA 7300
instructions manual, the guarantee given by Siemens will lapse. We urgently recommend using one
of the oils listed in the document "T 7300" (for a link to the internet, see back cover), because they have
been tested and meet the requirements.
Data, such as oil type, oil viscosity and approximately required oil quantity can be found on the rating
plate.

•

Check the oil level in the gear unit housing.

CAUTION

Risk of injury from chemical substances

The oil must not come into contact with the skin (e. g. the operator's hands).
The safety notes on the data sheets for the oil used must be observed here.
Remove any spilled oil immediately using an oil binding agent.
Observe the manufacturer's instructions for handling lubricants.
Wear suitable protective clothing.

7.1.6

Oil-supply system

The main gear unit is supplied with lubricating and cooling oil by the oil-supply system (see operating
instructions for the "Oil-supply system").

7.1.7

Checks before start-up

When the installation has been completed and before the start-up of the gear unit, inspect all drive parts
and remove all material residues, tools and installation aids.

Check the entire drive for the following:

□

Has the foundation been correctly constructed?

□

Are all the foundation bolts tightened to specification?

□

Has the gear unit been correctly fastened in place?

□

Has the grinding bowl been correctly installed?

□

Are the direction of rotation of the motor and that of the gear unit identical (see direction of rotation
arrow)?

□

Has the adhesive tape on the labyrinth seals been removed?

□

Has the round cord hollow profile been removed from the gear unit housing and the input flange?

□

Are all air filters installed?

NOTICE

Property damage

Damage to the gear unit due to absent or inadequate ventilation is possible.
Prior to start-up, the screw plug must be replaced with air filter.
Remove adhesive tape from the labyrinth seals.
Remove the round cord hollow profile between the gear unit housing and the input flange.

«
...
55
56
57
58
59
...
»

Содержание KMS


























































































Отзывы:

Нет отзывов

Похожие инструкции для KMS

Бренд: Panasonic Страницы: 30

Бренд: DBX Bushido Страницы: 12

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: MacDon Страницы: 74

Бренд: Fayat Group Страницы: 50

Бренд: Halyard Страницы: 88

Бренд: Laser Страницы: 2

Бренд: Lars Thrane Страницы: 50

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Nederman Страницы: 255

ST70 Instrument

Бренд: Raymarine Страницы: 12

Бренд: Raven Страницы: 73

Бренд: Tascam Страницы: 3

Бренд: RAB Lighting Страницы: 4

Бренд: campgo Страницы: 33

Бренд: Vahle Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды