Siemens KMS Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 89

background image

BA 9137 en 12/2015

10.7.2

Change oil

Note

Observe the separately attached operating instructions BA 7300 and the information in item 7.1.

•

Drain the oil while the gear unit is still warm, i.e. immediately after stopping it.

WARNING

Serious personal injury can be caused by switched-on machine

Shut down the gear unit and the oil-supply system to perform maintenance and/or repair work or prior
to removing the safeguards. Secure the drive unit against accidental start-up. Attach a notice on the
start switch stating clearly that work is in progress on the gear unit.

NOTICE

Property damage

Damage to the gear unit possible from inadequate lubrication because of mixed oils.
When changing the oil, always re-fill the gear unit with the same type of oil.
Never mix different types of oil and/or oils made by different manufacturers.
When changing to any different oil type, the gear unit must be flushed thoroughly using the new oil type.
Flushing is not necessary, if the new service oil is fully compatible with the old service oil in all respects.
Compatibility must be confirmed by the oil supplier. If there is a change to another oil grade or make,
Siemens recommends flushing out the gear unit with the new grade of service oil.

Note

When changing the oil, the housing and the oil-supply system (if present) must be cleaned thoroughly
from sludge, metal particles and oil residue by flushing it with oil. Use the same type of oil as is used
for normal operation. High-viscosity oils must be heated beforehand using suitable means. Ensure that
all residues have been removed before filling with fresh oil.

Note

In this regard, see Figure 9.

•

Place suitable containers under the oil drain cocks of the gear unit housing and of the

tilting pad thrust

bearing chamber.

•

Unscrew the screw plugs of the oil drain cocks and allow the oil to drain into the container.

CAUTION

Risk of scalding

Risk of injury from escaping hot oil.
Wear suitable protection gloves, protection glasses and protection clothing.
Remove any spilled oil immediately using an oil binding agent.
Observe environmental protection regulations.

•

If the oil-supply system is equipped with three-way cocks, the gear unit can be emptied through the
three-way cocks of the oil-supply system. The remaining residual oil must then be drained off through
the oil drain cocks on the gear unit (1, 2).

«
...
78
79
80
81
82
...
»

Содержание KMS


























































































Отзывы:

Нет отзывов

Похожие инструкции для KMS

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: ACE INSTRUMENTS Страницы: 15

Бренд: Wave Fitness Страницы: 15

Бренд: AcceleDent Страницы: 3

Бренд: Zero 88 Страницы: 32

Бренд: Parker Страницы: 5

Бренд: Bacharach Страницы: 31

Бренд: Bacharach Страницы: 2

Coronis 5MP Mammo

Бренд: Barco Страницы: 4

Бренд: Barco Страницы: 167

Color Coronis 2MP

Бренд: Barco Страницы: 156

Color Coronis 2MP

Бренд: Barco Страницы: 12

Бренд: Barco Страницы: 39

Бренд: Barco Страницы: 158

Бренд: fadini Страницы: 20

Бренд: Hacker Страницы: 2

Бренд: J.P. SELECTA Страницы: 8

Бренд: Haemonetics Страницы: 134

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды