Siemens FDCIO223 Скачать руководство пользователя страница 9

Страница: 9 / 72

About this document

Technical terms and abbreviations

9 | 72

Building Technologies

009122_h_en_--

Fire Safety

2016-05-04

1.3 Technical terms and abbreviations

Term

Explanation

ABS

Acrylonitrile-butadiene-styrene (plastic)

ASA

Acrylic ester-styrene-acrylnitrile (plastic)

EOL

Line termination element (end of line)

Product version

FDnet/C-NET

Addressed detector line

FC20xx

Fire control panel in 'Sinteso' fire detection system

FC72x

Fire control panel in 'Cerberus PRO' fire detection system

FS20

'Sinteso' fire detection system

FS720

'Cerberus PRO' fire detection system

I/O1

Input/output 1

I/O2

Input/output 2

KMK

Load factor for collective and conventional devices

(1 KMK 100 µA)

Collective detector

line

Non-addressed detector line (Siemens / GMT)

Conventional

detector line

Non-addressed detector line (industry standard)

LED

Light-emitting diode

MC link

Maintenance and Commissioning Link; interface to the

detector exchanger and tester

Polycarbonate (plastic)

SynoLINE300

Fire detection system for conventional detectors

SynoLINE600

Fire detection system for collective detectors

Synova300

Conventional fire detector

Synova600

Collective fire detector

Содержание FDCIO223









































































Результаты поиска

Содержание FDCIO223

Отзывы:

Бренды по названию

Популярные бренды

Siemens FDCIO223, Техническое руководство

Результаты поиска

Содержание FDCIO223

Отзывы:

Бренды по названию

Популярные бренды