manualshive.com logo in svg

Siemens FDCIO223, Техническое руководство

Поделиться
Скачать
Siemens FDCIO223 Скачать руководство пользователя страница 16

Safety
Standards and directives complied with

2

16 | 72
Building Technologies

009122_h_en_--

Fire Safety

2016-05-04

2.3 Standards and directives complied with

A list of the standards and directives complied with is available from your Siemens

contact.

2.4 Release Notes

Limitations to the configuration or use of devices in a fire detection installation with

a particular firmware version are possible.

WARNING

Limited or non-existent fire detection
Personal injury and damage to property in the event of a fire.

Read the 'Release Notes' before you plan and/or configure a fire detection

installation.

Read the 'Release Notes' before you carry out a firmware update to a fire

detection installation.

NOTICE

Incorrect planning and/or configuration
Important standards and specifications are not satisfied.
Fire detection installation is not accepted for commissioning.
Additional expense resulting from necessary new planning and/or configuration.

Read the 'Release Notes' before you plan and/or configure a fire detection

installation.

Read the 'Release Notes' before you carry out a firmware update to a fire

detection installation.

Содержание FDCIO223









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды