Siemens FDCIO223 Скачать руководство пользователя страница 55

Страница: 55 / 72

Mounting / Installation

Connecting input/output module

55 | 72

Building Technologies

009122_h_en_--

Fire Safety

2016-05-04

5.3 Connecting input/output module

Connect the module in accordance with the corresponding connection diagrams.

NOTICE

Incorrectly connected input/output module
Damage to the device

Never connect the external DC 24 V power supply or the FDnet/C-NET

detector line to the green terminals of input/output 'I/O 1' or input/output

'I/O 2'.

Observe the assignment of terminals as per chapter 'Printed circuit board

view [ 21]'.

Do not connect the external DC 24 V power supply until you have configured the

input/output module FDCIO223.

Note the positive and negative poles.
Only connect one wire per terminal. This is the only way to ensure the connection

is failure-free for the entire service life of the device.

1 Internal fuse max. 0.7 AT

2 External fuse power supply

max. 2 AT

I/O 2

I/O 1

DC 24 V

FDnet
C-NET

Содержание FDCIO223









































































Результаты поиска

Содержание FDCIO223

Отзывы:

Бренды по названию

Популярные бренды

Siemens FDCIO223, Техническое руководство

Результаты поиска

Содержание FDCIO223

Отзывы:

Бренды по названию

Популярные бренды