Siemens FDCIO223 Скачать руководство пользователя страница 44

Страница: 44 / 72

Structure and function
Diagnosis levels

44 | 72
Building Technologies

009122_h_en_--

Fire Safety

2016-05-04

Control methods involving pulse patterns

Control methods involving pulse patterns reduce the service life of the relay

contacts on the input/output module. Contact wear is also dependent on the load.

Up to 300,000 switching cycles are permitted.

At one switching cycle per second, 300,000 switching cycles are reached after

approx. 3.5 days.

Behavior in the event of an error (control panel-specific)

Error

Configuration option

Failure of 24 V power supply

Open (configuration not possible)

Error involving control panel (e.g.,

communication with control panel

interrupted)

Relay remains unchanged
Relay deactivated
Relay activated
Degraded mode horn function (only possible with control panels

FC20xx and FC72x)

In the case of the 'Degraded mode horn' function, the input/output module

accepts the 'Sounder ON' command. This function can only be configured on

control panels FC20xx and FC72x.
The monitoring of monitored control systems will only be resumed 30 seconds

after deactivation.

3.4.4.5 Control with confirmation

Control with confirmation is not supported by the following control panels or the

confirmation is not configured or processed on the control panel:

FC20xx
FC72x
AlgoRex

3.5 Diagnosis levels

The FDCIO223 input/output module monitors its operation largely autonomously.
The following diagnosis levels are derived from the different control measurements:

Normal
Observe information
Replacement recommended
Replacement necessary
Fault

For details, see table below.
When an error occurs which impairs the correct functionality of the module, a

module fault message is reported. The module contains additional information for

addressing the cause. This can be displayed by the FDUD292 detector exchanger

and tester or FDUD293 intelligent detector tester for example.
You will find more information in documents 007227 and 009718.

Содержание FDCIO223









































































Результаты поиска

Содержание FDCIO223

Отзывы:

Бренды по названию

Популярные бренды

Siemens FDCIO223, Техническое руководство

Результаты поиска

Содержание FDCIO223

Отзывы:

Бренды по названию

Популярные бренды