Siemens CERBERUS PYROTRONICS PXL Скачать руководство пользователя страница 62

Страница: 62 / 83

PXL Conventional Fire Alarm Control Panel

Testing and Troubleshooting

TROUBLE MESSAGES

Trouble Message Text

Condition

Possible Cause

System powers up normally but
nothing shows on LCD display

Contrast not adjusted properly

AC POWER FAULT

AC power off/low

• Loss of AC mains
• AC brownout
• Blown secondary fuse
• Open transformer primary/secondary

BELL XX

NAC trouble

NAC open
NAC shorted

BELL XX BYPASSED

NAC bypassed

GROUND FAULT

Ground fault

• +24 shorted to earth ground
• -V shorted to earth ground
• F+, R+, R-, F- of an NAC shorted
to earth ground
• IDC+ or IDC- of an IDC zone
shorted to earth ground

INCORRECT PZE PIC

Firmware error for CANADA
country selection

PCM-1 and/or PZE-4B module has Rev. 1.0
firmware. Upgrade to Rev. 3.x or higher

LED MOD X MULTI/UNKN

LED-3/4 not responding and ASC
routine will not run

Two or more LED-3/4s installed with same
dipswitch address

LED-3/4 MOD X NO
RESPONSE

LED-3/4 not responding

• Module removed from system*
• Module failed
• Module address changed

LED-3/4 MOD X NOT SPEC’D

LED-3/4 responding but not in
configuration

• LED module added but system not
reconfigured
• LED module address changed

MULTI RESP LED-3/4 MOD X

Multiple Response at LED-3/4
address

• Two LED modules set to same address
• LED set to address out of range

MULTI RESP PCM MOD O

Multiple Response at PCM
address

Module failed

MULTI RESP PNC MOD X

Multiple Response at PNC
address

• Two PNC modules set to same address
• PNC set to address out of range

MULTI RESP PPS MOD X

Multiple Response at PPS
address

• Two PPS modules set to same address
• PPS set to address out of range

MULTI RESP PRM MOD X

Multiple Response at PRM
address

• Two PRM modules set to same address
• PRM set to address out of range

MULTI RESP PZE MOD X

Multiple Response at PZE
address

• Two PZE modules set to same address
• PZE set to address out of range

MULTI RESP RSA MOD X

Multiple Response at RSA
address

• Two RSA modules set to same address
• RSA set to address out of range

* Modules purposely removed from the system may be removed from the configuration using
the "Delete Module Option" in the Program menu.

X = Module number

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Содержание CERBERUS PYROTRONICS PXL




















































































Результаты поиска

Содержание CERBERUS PYROTRONICS PXL

Отзывы:

Похожие инструкции для CERBERUS PYROTRONICS PXL

Бренды по названию

Популярные бренды

Siemens CERBERUS PYROTRONICS PXL, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CERBERUS PYROTRONICS PXL

Отзывы:

Похожие инструкции для CERBERUS PYROTRONICS PXL

Бренды по названию

Популярные бренды