manualshive.com logo in svg

Siemens 6GK5748-1GY01-0AA0, Руководство по эксплуатации, Страница: 64 / 91

Поделиться
Скачать
Siemens 6GK5748-1GY01-0AA0 Скачать руководство пользователя страница 64

Connection 

 

6.2 Power supply 

 

SCALANCE W1788-x / W1748-1 

64

 

Operating Instructions, 03/2022, C79000-G8976-C484-05 

Position and pin assignment 

 

①

 

M12 interface, direct feed in, A-coded, 4-pin 

②

 

M12 Ethernet port P2 LAN PoE, X-coded, 8-pin 
The power can also be supplied via this interface (Power over Ethernet). 
Pin assignment, see Ethernet (Page 66) 

③

 

M12 Ethernet port P1 LAN, X-coded, 8-pin 

The four-pin M12 socket has the following pin assignment: 

 

Pin 

Signal 

Assignment 

1 

L1+ 

24 VDC 

2 

L2+ 

24 VDC 

3 

M 

Ground 

4 

M 

Ground 

Connecting/disconnecting the power supply 

 

 

WARNING 

Danger from electric shock 

Turn off the power supply before you insert or remove the plug of the power supply. 

 

1.

 

Connect the plug and socket. Make sure that they lock in place correctly. 

2.

 

Tighten the knurled screw (tightening torque 1 Nm). 

Содержание 6GK5748-1GY01-0AA0




























































































Отзывы:

Нет отзывов