Siemens 6GK5748-1GY01-0AA0 Скачать руководство пользователя страница 36

Страница: 36 / 91

Description of the device

4.5 LED display

SCALANCE W1788-x / W1748-1

Operating Instructions, 03/2022, C79000-G8976-C484-05

LED

Color

Meaning

Off

No fault/error.

Red

The device is starting up or an error has occurred.

Flashing red

Interval:

500 ms on / 500 ms off

The bootloader waits in this state for a new firmware file that

you can download by TFTP.

Flashing red

Interval:

2000 ms on / 200 ms

off

Firmware on PLUG:
The device is performing a firmware update or downgrade.

Red

Simultaneous

R1/R2 yellow flashing

A competing radar signal was found on all enabled channels.

Flashing yellow

The port LEDs flash for detection of device location.
The "LED flash" function is activated
•

Either with SINEC PNI

•

Or via the WBM page "Discovery and Set via DCP"

Note
Primary user (radar) on all enabled channels

If the device detects a competing radar signal on all enabled channels of the WLAN

interfaces, the

LED is lit and

flash. No data traffic is then possible for the next

30 minutes. After this time, the device runs the scan again and checks whether a primary

user still exists. If no primary user is detected, data traffic is possible again.
The wait time of 30 minutes is necessary due to legal requirements and cannot be

shortened even by restarting the device.

Содержание 6GK5748-1GY01-0AA0




























































































Результаты поиска

Содержание 6GK5748-1GY01-0AA0

Отзывы:

Siemens 6GK5748-1GY01-0AA0, Руководство по эксплуатации, Страница: 36 / 91

Результаты поиска

Содержание 6GK5748-1GY01-0AA0

Отзывы: