Siemens 6GK5748-1GY01-0AA0 Скачать руководство пользователя страница 23

Страница: 23 / 91

Description of the device

4.3 Components of the product

SCALANCE W1788-x / W1748-1
Operating Instructions, 03/2022, C79000-G8976-C484-05

4.3

Components of the product

The following components are supplied with the product:
• A SCALANCE device with pre-installed bracket for securing to a DIN rail
• Two grounding screws
• One cover for PLUG slot
• Three protective caps for the M12 sockets

–

2 x Ethernet

–

1 x power supply

• Protective caps for the antenna sockets:

–

4 x for SCALANCE W1788-1 / W1748-1

–

8 x for SCALANCE W1788-2

Note

The wall mounting set and the bracket set for securing the device to a standard rail are

not included in the scope of delivery, see Accessories (Page 24).

Please check that the consignment you have received is complete. If the consignment is

incomplete, contact your supplier or your local Siemens office.

Содержание 6GK5748-1GY01-0AA0




























































































Результаты поиска

Содержание 6GK5748-1GY01-0AA0

Отзывы:

Siemens 6GK5748-1GY01-0AA0, Руководство по эксплуатации, Страница: 23 / 91

Результаты поиска

Содержание 6GK5748-1GY01-0AA0

Отзывы: