Siemens 6GK5748-1GY01-0AA0 Скачать руководство пользователя страница 38

Страница: 38 / 91

Description of the device

4.7 Configuration License PLUG

SCALANCE W1788-x / W1748-1

Operating Instructions, 03/2022, C79000-G8976-C484-05

NOTICE
Previous settings

If you reset, all the changes you have made will be overwritten by factory defaults.

NOTICE
Inadvertent reset

An inadvertent reset can cause disturbances and failures in a configured network with

further consequences.

4.7

Configuration License PLUG

The CLP (Configuration License PLUG) is used to transfer the configuration of the old

device to the new device when a device is replaced. The CLP is also referred to as PLUG

in the description.
The PLUG is available in the following variants:
•

PLUG Configuration: The exchangeable storage medium only saves the configuration

data of the device.

•

PLUG License: In addition to the configuration data, the exchangeable storage

medium contains a license with which special functions are enabled, e.g. iFeatures.

NOTICE
Loss of the degree of protection

When the cover is not mounted correctly, the device loses its degree of protection IP65

and is not water and dust proof.

Position

The CLP slot is at the bottom of the device enclosure under a cover, see Reset button

(Page 37).

Содержание 6GK5748-1GY01-0AA0




























































































Результаты поиска

Содержание 6GK5748-1GY01-0AA0

Отзывы:

Siemens 6GK5748-1GY01-0AA0, Руководство по эксплуатации, Страница: 38 / 91

Результаты поиска

Содержание 6GK5748-1GY01-0AA0

Отзывы: