Siemens 6GK5748-1GY01-0AA0 Скачать руководство пользователя страница 32

Страница: 32 / 91

Description of the device

4.5 LED display

SCALANCE W1788-x / W1748-1

Operating Instructions, 03/2022, C79000-G8976-C484-05

LED

Color

Meaning

Flashing green and

yellow

Data transfer via the WLAN interface 1.

Flashing yellow

Interval:

100 ms on / 100 ms

off

Access point mode:

With DFS (802.11h), the channel is scanned for one minute for

competing radar signals before the channel can be used for data

traffic.

Off

No fault/error.

Red

The device is starting up or an error has occurred.

Flashing red

Interval:

500 ms on / 500 ms

off

The bootloader waits in this state for a new firmware file that you

can download by TFTP.

Flashing red

Interval:

2000 ms on /

200 ms off

Firmware on PLUG:
The device is performing a firmware update or downgrade.

Red

Simultaneous

R1 yellow flashing

A competing radar signal was found on all enabled channels.

Flashing green

The port LEDs flash for detection of device location.
The "LED flash" function is activated
•

Either with SINEC PNI

•

Or via the WBM page "Discovery and Set via DCP"

Содержание 6GK5748-1GY01-0AA0




























































































Результаты поиска

Содержание 6GK5748-1GY01-0AA0

Отзывы:

Siemens 6GK5748-1GY01-0AA0, Руководство по эксплуатации, Страница: 32 / 91

Результаты поиска

Содержание 6GK5748-1GY01-0AA0

Отзывы: