Siemens 6GK5748-1GY01-0AA0 Скачать руководство пользователя страница 29

Страница: 29 / 91

Description of the device

4.4 Accessories

SCALANCE W1788-x / W1748-1
Operating Instructions, 03/2022, C79000-G8976-C484-05

Antennas

Type

Properties

Article number

ANT792-4DN

RCoax helical antenna, circular

polarization, 4 dBi, 2.4 GHz, N-Connect

female.

6GK5792-4DN00-0AA6

ANT792-6MN

Omni antenna, mast/wall mounting, 6 dBi

2.4 GHz, N-Connect female

6GK5792-6MN00-0AA6

ANT792-8DN

Directional antenna, mast/wall mounting,

14 dBi 2.4 GHz, N-Connect female

6GK5792-8DN00-0AA6

ANT793-6DG

Wide angle antenna, mast/wall mounting,

9 dBi 5 GHz, 2 x N-Connect female

6GK5793-6DG00-0AA0

ANT793-8DJ

Directional antenna, mast/wall mounting,

18 dBi 5 GHz, 2 x N-Connect female

6GK5793-8DJ00-0AA0

ANT793-8DK

Directional antenna, mast/wall mounting,

23 dBi 5 GHz, 2 x N-Connect female

6GK5793-8DK00-0AA0

IWLAN RCoax
ANT793-4MN

RCoax

4 antenna with vertical

polarization for RCoax systems, 6 dBi,

5 GHz, IP65, N-Connector female

6GK5793-4MN00-0AA6

ANT795-4MC

Omnidirectional antenna, 3/5 dBi, 2.4 GHz

and 5 GHz, IP65, N-Connect male for

direct installation on the device, straight

connector.

6GK5795-4MC00-0AA3

ANT795-4MD

Omnidirectional antenna, 3/5 dBi, 2.4 GHz

and 5 GHz, IP65, N-Connect male for

direct installation on the device, 90°

connector.

6GK5795-4MD00-0AA3

ANT795-6DC

Wide angle antenna, mast/wall mounting,

9 dBi 2.4 GHz and 5 GHz, N-Connect

female

6GK5795-6DC00-0AA0

ANT795-6MN

Omni antenna, mounted on roof/vehicle,

6/8 dBi 2.4 GHz and 5 GHz, N-Connect

female

6GK5795-6MN10-0AA6

ANT793-8DL

Directional antenna vertical-horizontal

polarized, 5 GHz, 14dBi, IP66, 2 x N-

Connector female

6GK5793-8DL00-0AA0

ANT793-8DP

Directional antenna, mast/wall mounting,

13 / 13.5 dBi 4.9 GHz and 5 GHz, N-

Connect female

6GK5793-8DP00-0AA0

ANT795-4MX

Omnidirectional antenna, 2/2.5 dBi,

2.4 GHz and 5 GHz, IP69K, N-Connector

male

6GK5795-4MX00-0AA0

ANT795-6MP

Omnidirectional antenna, 5/7 dBi, 2.4 GHz

and 5 GHz, IP65/67, N-Connector female

6GK5795-6MP00-0AA0

IWLAN RCoax Cable

2,4 GHz PE 1/2"

Omni antenna, 0 dBi 2.400 - 2.485 GHz, N-

Connect female

6XV1875-2A

IWLAN RCoax Cable

5 GHz PE 1/2"

Omni antenna, 0 dBi 5.150

–

5.875 GHz, N-

Connect female

6XV1875-2D

Содержание 6GK5748-1GY01-0AA0




























































































Результаты поиска

Содержание 6GK5748-1GY01-0AA0

Отзывы:

Siemens 6GK5748-1GY01-0AA0, Руководство по эксплуатации, Страница: 29 / 91

Результаты поиска

Содержание 6GK5748-1GY01-0AA0

Отзывы: