Sidite SR882 страница 20 Скачать руководство пользователя

Страница: 20 / 56

SR882 operation manual

~ 19 ~

The second schedule:

from 10:00 to 10:00 am, it means there is no back-up heating in this

time.

The third schedule:

back-up heating function starts at 17:00 and ends at 22:00 pm.

Within this time section, the switch-on temperature is 50

C; switch-off temperature is 55

The switch-on temperature adjustable range: 10

C ~ (OFF-2

The switch-off temperature adjustable range: (ON+2

C) ~ 80

If you want to shut off one timing heating, then you can set the turning on time and turning

off time with a same value ( for example, no this function during the second time section,

then you can set turning on/off time is 10:00 ~ 10:00)

When time is outside of the preset schedule, back-

up heating doesn’t work automatically

even when the tank temperature reaches the switch

–on temperature of heating.

Note:



When there is no sensor installed in the top part of tank (no T3 sensor), controller will

take the signal of T2 (sensor in bottom of tank) automatically to control this function.



The time in this controlled is 24 hours mode, when you set schedule, the switch-off

time of heating should be larger than the switch-on time. For example: if you set the

switch-on time of heating is at 17:00, but switch-off time of heating is 6:00, then this

setting doesn’t take effect, that means within this time section, heating function doesn’t

work. The correct set is like flowing: it should be divided into two time sections, one

time section is from 17:00 to 23:59, the other time section is from 00:00 to 06:00.

Setup steps:

under standby status.

► Press “SET” button, then press “+” button, “tHET” menu displays on the screen.

► Repress “SET” button, to access “tHET” program,

► Repress “SET” button, to access parameter setting

window of tHET program,

“tH 1o 04:00” displays on

screen, “04” of hour time blinks on screen, the

switch-on time and temperature for the first schedule

of heating function can be

►Press “+”“-” button to adjust hour of time

►Repress “SET” button again, “00” of minute time blinks on screen

Содержание SR882

























































Результаты поиска

Содержание SR882

Отзывы:

Похожие инструкции для SR882

Бренды по названию

Популярные бренды

Sidite SR882, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SR882

Отзывы:

Похожие инструкции для SR882

Бренды по названию

Популярные бренды