Sidite SR882 страница 18 Скачать руководство пользователя

Страница: 18 / 56

SR882 operation manual

~ 17 ~

2.6 System description

Note:

T3 is alternative sensor, when no sensor (T3) is installed on the top part of tank, controller

will use the signal of sensor T2 automatically to control the auxiliary heating or the

circulation pump.

1 collector array

– 1 storage tank – 1 pump and auxiliary heating

Description:

The solar circuit pump (P1) is switched on as soon as the switch-on temperature difference

(

△

Ton) between the collector array (T1) and the storage tank (T2) is reached. If the

temperature difference between the collector array (T1) and storage tank (T2) drops below

the switch-off temperature difference (

△

Toff), or the temperature of storage tank (T3)

reaches the preset maximum storage temperature, then the solar circuit pump (P1) is

switched off.

Back-up heating by auxiliary boiler

(detailed see paragraph 3.2):

Within the preset schedule of back-up heating, if the temperature T3 is below the preset

switch-on temperature, then the back-up heating

（

）

is triggered, when T3 is heated to

the preset switch-off temperature, back-up heating H1 is ceased.

T1: Sensor on collector array

T2: Sensor on the bottom part of tank.

T3: Sensor on the top part of tank

(optional sensor)

T4: Sensor on hot water pipe, on solid

fuel boiler or for thermostat (alternative)

T5: Sensor on tank return pipe (for

measuring thermal energy)

T6: Sensor on tank flow pipe

P1: Solar circuit pump

P2: Hot water circuit pump, solid fuel boiler circuit pump, output for thermostat or output for

high temperature cooling (Note: this output can only used as one of above mentioned four

functions, depend on which function is activated)

H1: Output for back-up electrical heater

Содержание SR882

























































Результаты поиска

Содержание SR882

Отзывы:

Похожие инструкции для SR882

Бренды по названию

Популярные бренды

Sidite SR882, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SR882

Отзывы:

Похожие инструкции для SR882

Бренды по названию

Популярные бренды