SICK IDM series Скачать руководство пользователя | Manualshive

Страница: 13 / 134

background image

Operating Instructions

Preparation before using

IDM corded & IDM Bluetooth

8017159/142O/2019-05-23

© SICK AG · Germany · All rights reserved · Subject to change without notice

13

2.1.3

Placing the scanner into the cradle

Ensure that the scanner is placed properly into the respective smart or charging cradle. If the unit is not
placed correctly into the cradle, the charging might not start.

IDMx41: Insert the scanner

vertically

IDMx61: Insert the back of the scanner first.

Afterwards push the scanner head down.

The correct placement into the cradle can be verified by the charging LED on the scanner. (See also chapter
2.1.5 on page 14)

2.1.4

USB Bus power

•

If USB 3.0 is available in your host device, both battery charging and regular operation can be
supported by the USB Bus Power without using external power supply.

•

If you want to use this feature, set the USB bus power switch to “ON”. Then connect the cradle and
host device via an USB cable.

•

If only USB 2.0 is available in your host device the external power supply is necessary as a power
source, because the power supplied from USB 2.0 is not enough to support both battery charging and
regular operation simultaneously.

Important information

: Please charge the new battery pack for

8 hours

prior to the first use. Ensure

that you are using a battery with enough capacity. Otherwise the scanner might lose its radio
connection. As soon as the scanner gives warning messages (one red blink and one beep at a regular
interval) the scanner needs to be recharged. If the scanner gives 8 red blinks and 8 beeps, the battery
power is extremely low. In that case the battery needs to be recharged immediately! If the scanner is
not placed into the charging cradle right the way, the scanner turns off automatically. Due to an internal
protection circuit there will now be measured 0 V on the outside contacts of the battery. If the battery
is not recharged immediately, a further discharge takes place even though the scanner is turned off.
Due to the internal chemical processes of lithium ion batteries, this will then result in an irreversible
destruction of the battery.

«
...
11
12
13
14
15
...
»

Содержание IDM series







































































































































Отзывы:

Нет отзывов

Похожие инструкции для IDM series

Бренд: Fametech Страницы: 40

Бренд: Magtek Страницы: 70

Бренд: SATO Страницы: 2

Бренд: Lindy Страницы: 2

Бренд: Hama Страницы: 24

Бренд: Stid Страницы: 3

Бренд: Stid Страницы: 10

Бренд: ViewSonic Страницы: 73

Бренд: Sunstech Страницы: 37

Бренд: Shintaro Страницы: 12

Бренд: TSC Страницы: 44

Бренд: DOSMONO Страницы: 7

Hanlin eReader V5

Бренд: Jinke Страницы: 53

Hanlin eReader V3+

Бренд: Jinke Страницы: 54

Бренд: FAMOCO Страницы: 16

Бренд: RealTrace Страницы: 2

Бренд: Opticon Страницы: 59

Бренд: Interlogix Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды