manualshive.com logo in svg

Sib Geofiz Pribor SGD-TG, Руководство по эксплуатации

Поделиться
Скачать
Sib Geofiz Pribor SGD-TG Скачать руководство пользователя страница 29

Sib Geofiz Pribor Ltd

4.4.10.2. Backlight OFF time

The parameter can take values “No”  and from 1 to 60 minutes.  The parameter value 
can be changed both by the use of LEFT and RIGHT arrows and by entering a number. 
Entering “0” corresponds to the “No” value. 

If this parameter has a nonzero value, then, upon expiration of the preset time (1-60 
minutes)   after   any   button   was   pressed   last,   display  backlight  will   switch   off 
automatically. Backlight will switch on again upon pressing any button.

Switching off backlight reduces power consumption and increases duration of operation 
from the battery without charging.

4.4.10.3. LCD contrast

The parameter can take values from 20% to 90%. The parameter value can be changed 
both by the use of LEFT and RIGHT arrows and by entering a number.

4.4.10.4. Key beeps

This parameter can take values “No” and “Yes”. The parameter value can be changed 
using   the   LEFT   and   RIGHT   arrows.    With   the   “No”   value,   a   short   audible   signal 
accompanying pressing of buttons will be disabled.

4.4.11. 

HW diagnostics… - Display

4.4.11.1. Screen

Execution of this menu option causes all screen points to switch on. This enables 
checking integrity of the display, i.e., the absence of faulty points. This checking is 
stopped by pressing the ESC button.

4.4.11.2. Backlight

Execution   of   this   menu   option   causes   saw-tooth   variations   of   the   display  backlight 
brightness   from   minimum   to   maximum   and   backward.  This   checking   is   stopped   by 
pressing the ESC button.

4.4.11.3. Contrast

Execution of this menu option causes saw-tooth variations of the display contrast from 
minimum to maximum and backward. This checking is stopped by pressing the ESC 
button.

4.4.11.4. Keypad

Execution of this item results in cleaning the bottom (information) portion of the screen. 
Besides, pressing any button (apart from ON-OFF) causes identification mark of the 
pressed button to be displayed in the bottom part of the screen. Once the button is 
released, the identification mark disappears. This enables to check normal operation of 
all buttons. This checking is stopped by pressing and releasing the ESC button.

4.4.11.5. Sound

Execution   of   this   menu   option   causes   variable   tone   audible   signal   to   sound 
continuously.  This checking is stopped by pressing the ESC button.

29

Содержание SGD-TG















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды