SIATA Aqua Timer Plus Скачать руководство пользователя страница 17

Страница: 17 / 34

Aqua Timer Plus

17/34

Program

3 H L

3 H L 0

FLAG not used.

Leave programmed at 0

Program

0 C L

0 C L 0

Modality of the litre counter divider.

Do not use

See par. 6.6

Program

1 C L

1 C L 0

Standard regeneration.

See par. 6.8

Advance

1 C L

1 C L 1

Regeneration with stand-by

Program

2 C L

2 C L 0

Duplex distributor with standard cams.

See par.

6.8

Advance

2 C L

2 C L 1

Duplex distributor with stand-by cams

Program

3 C L

3 C L 0

Management of salt alarm

disabled

Advance

3 C L

3 C L 1

Management of salt alarm

enabled. See par. 6.9

Program

0 d L

0 d L 0

Normal functioning

Advance

0 d L

0 d L 1

Management of the start of the regeneration in the case of inhibit.

See par. 6.12

Program

1 d L

1 d L 0

FLAG not used

Program

2 d L

2 d L 0

FLAG not used

Program

3 d L

3 d L 0

FLAG not used

Program

Fast flashing of the display. The programming is memorised in eeprom.

6.2.4.c – List of codes to be programmed

For the programming and the meaning of the codes see par. 6.3. In this modality the programming of the following

codes is recommended:

Tab. 16 – Table of the codes in one duplex column modality LLL2 – LL–1

Code

Meaning

SC02

Programming of the time of regeneration between two regenerations

SC03

Programming of the regeneration cycle ( stop times )

SC05

Programming of the duration of the end of cycle impulse and of the litre counter divider of the

dosing pump

SC00

Initialisation of the system

Содержание Aqua Timer Plus



































Результаты поиска

Содержание Aqua Timer Plus

Отзывы:

Похожие инструкции для Aqua Timer Plus

Бренды по названию

Популярные бренды

SIATA Aqua Timer Plus, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aqua Timer Plus

Отзывы:

Похожие инструкции для Aqua Timer Plus

Бренды по названию

Популярные бренды