SHOWTEC 50701 Скачать руководство пользователя страница 18

 

  

 

 

17 

   

 

Ordercode: 50701 

SM-16/2 

Maintenance 

The operator has to make sure that safety-related and machine-technical installations are to be 
inspected by an expert after every year in the course of an acceptance test. 
The operator has to make sure that safety-related and machine-technical installations are to be 
inspected by a skilled person once a year. 
 
The following points have to be considered during the inspection: 
01)

 

All screws used for installing the device or parts of the device have to be tightly connected and 
must not be corroded. 

02)

 

There may not be any deformations on housings, fixations and installation spots. 

03)

 

The electric power supply cables must not show any damages or material fatigue. 

 

The 

Showtec SM-16/2 

requires almost no maintenance. However, you should keep the unit clean.  

Disconnect the mains power supply, and then wipe the cover with a damp cloth. Do not immerse in 
liquid. Do not use alcohol or solvents. 
Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections 
with a damp cloth. Make sure that the connections are thoroughly dry before linking equipment or 
supplying electric power. 

 
 

Troubleshooting 

This troubleshooting guide is meant to help solve simple problems.  
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit 
operates properly, do not carry out following steps. 
 
Showtec SM-16/2 
This troubleshooting guide is meant to help solve simple problems. If a problem occurs, carry out the steps 
below in sequence until a solution is found. Once the unit operates properly, do not carry out following 
steps. 
01)

 

Fixture does not respond to controller: Check the DMX-address of the fixture and the controller.    
Make sure they match. Make sure the connections are correct. Check if blackout is off. 

02)

 

Interference between chases; If the same channel has been assigned to different running chases, 
the one with the highest channel value will be put out. 

03)

 

Note: when in programming mode, as long as the LED indicator is lit, the value will be stored, even if  
the value is zero. 

04)

 

Except for the channels assigned to the jog wheels and the channels set with slope,

 

slope is not  

assigned to the other channels. 

05)

 

For the master controlled channels, the master sliders are only valid when the dimmer buttons are  
activated (LED indicator is on). If some channels cannot be controlled, please check if they are 
assigned to the master control. 

06)

 

If the device does not operate properly, unplug the device. 

07)

 

Check power from the wall, all cables, the fuse, the settings (return to default), etc. 

08)

 

If all of the above appears to be O.K., plug the unit in again. 

09)

 

If nothing happens after 30 seconds, unplug the device. 

10)

 

Return the device to your Showtec dealer. 

 
 

 

Содержание 50701





















Отзывы: