Shield M10U Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 72

Shield M10U Скачать руководство пользователя страница 57

Chapter 7 Operator Control and Display Panel

48

Shield M10U user manual

ESC Mute

Transfer to Bypass

B

I

Fig.7- 11: System Operate

Menu of Operate includes:

Functional operation

Mute off or mute on.

Fault clear manually

Manually transfer to bypass or escape from bypass mode

Transfer to inverter mode manually. The output could be interrupted.

Enable the “OFF” button on the front panel of power module. Then the “OFF” button is available, user can

press the button to shutdown the power module.

Reset battery history data including discharge dates and hours, discharge times. Normally reset battery

history data after replacing new batteries.

Reset dust filter data including days and maintenance period. Normally reset filter data after replacing new

filter or washing.

Command

Battery test command. UPS transfer to battery mode, main LED indicator is dark and battery LED indicator

green flashes. If battery is sick or battery is failure, UPS will alarm and transfer back to normal mode or transfer to bypass
mode. Make sure there is not any warns or alarm, make sure that battery voltage is higher than 90% of float voltage. If
battery is normal, UPS will transfer back to normal mode after 20 seconds. If battery test is failure, UPS alarms in the
history log.

Battery maintenance command. UPS transfer to battery mode, main LED indicator is dark and battery LED

indicator green flashes. Make sure that there is not any warns or alarm, make sure that battery voltage is higher than 90%
of float voltage. If battery is normal, UPS will transfer back to normal mode until battery voltage is down to 105% of EOD
voltage and then transfer back to normal mode.

Manually enable charger enter in boost charge mode to charge the batteries more quickly.

Manually enable charger enter in float charge mode.

Stop battery test or battery maintenance.

Enter in main menu

to see the waveform of output voltage, current and bypass voltage.

«
...
55
56
57
58
59
...
»

Содержание M10U









































































Отзывы:

Нет отзывов