Shield M10U Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 72

Shield M10U Скачать руководство пользователя страница 44

Chapter 6 Operating Instructions

Shield M10U user manual

35

Warning

During this procedure the UPS output terminals are live. If any load equipment are connected to the UPS output
terminals please check with the load user that it is safe to apply power: If the load is not ready to receive power then
ensure that it is safely isolated from the UPS output terminals.

2.

Close external output circuit breaker. Close external mains input circuit breaker and connect the mains power.

The LCD starts up at this time. The Rectifier indicator flashes during the startup of rectifier. The rectifier enters
normal operation state, and after about 20s, the rectifier indicator goes steady green. After initialization, the bypass
static switch closes. The UPS Mimic LEDs will indicate as following:

LED

Status

Rectifier indicator

Green

Battery indicator

Red

Bypass indicator

Green

Inverter Indicator

Off

Load indicator

Green

Status indicator

Red

3.

The inverter starts up automatically.

The inverter indicator flashes during the startup of inverter. After about

1minute, the inverter is ready, the UPS transfers from bypass to inverter, the bypass indicator turns off, and the
inverter and load indicators turn on. The UPS is in normal mode. The UPS Mimic LEDs will indicate as following:

LED

Status

Rectifier indicator

Green

Battery indicator

Red

Bypass indicator

Off

Inverter Indicator

Green

Load indicator

Green

Status indicator

Red

4.

Close external battery switch, battery indicator turns off, a few minutes later, the battery will be charged by UPS.
The UPS Mimic LEDs will indicates as following:

LED

Status

Rectifier indicator

Green

Battery indicator

Green

Bypass indicator

Off

Inverter Indicator

Green

Load indicator

Green

Status indicator

Green

Note

The panel on 6-power modules cabinet has 6 mimic indicators: rectifier, inverter, bypass, battery, load, status.

The panel on 2/4-power modules cabinet has only status LED.

6.2.2 Procedures for Switching Between Operation Modes

Switch from normal mode to bypass mode

Press “

” menu in menu “operate” to switch to bypass mode.

Note

In bypass mode, the load is directly fed by the mains power instead of the pure AC power from the inverter.

Switch from bypass mode to normal mode

Press “

” menu in bypass mode. After the inverter enters in normal operation, the UPS transfers to normal mode.

警告

危险

警告

危险

警告

危险

«
...
42
43
44
45
46
...
»

Содержание M10U









































































Отзывы:

Нет отзывов