background image

 

 

SAFETY PRECAUTIONS

 

A careful operator is the best operator. Most accidents can be avoided by observing certain safety 
precautions.  Read and understand these precautions before operating the Front Mounted Mower. 
This equipment should be operated only by those who have been trained in its safe use. 
 

THE MOWER 

Know and understand all mower instructions and 
Safety Precautions before assembly, service, or 
operation. Also read and understand all Safety 
Precautions in the Tractor Operators Manual.

 

Keep the tractor and mower in good operating 
condition at all times. Always keep all shields 
and guards securely in place.

 

Make sure all fastening hardware is properly 
tightened before operating the tractor and 
mower.

 

Keep all Safety Decals clean and free of dirt and 
grime. Always replace any Safety Decals that 
become damaged, lost, painted over, or 
otherwise become illegible. Replace all Safety 
Decals when repainting the cutter 

 

MOWER OPERATION 

DO NOT permit anyone but the operator to ride 
on the tractor and mower. There is no safe place 
on this equipment for passengers.

 

Clear the area of all visible debris before 
beginning mowing operations.

 

Mow only during daylight hours, or when the 
area is well lit artificially.

 

To avoid loss of control, and to prevent 
overturning the tractor and mower, always mow 
up and down slopes, never across. DO NOT 
operate on steep slopes. 
Always slow down when turning.

 

Always keep mower discharge directed away 
from people or animals, which could be injured, 

and away from objects that could be damaged  
by debris thrown by the mowing blades.

 

To avoid the possibility of injury from flying 
debris, NEVER operate the mower raised into 
the transport position.

 

Slop and inspect all parts of the mower after 
striking any foreign object. Repair any damage 
before resuming mowing operations.

 

Disengage power to the mower and make sure 
the area behind the tractor and mower is clear 
before backing up.

 

The operator should NEVER leave the tractor 
seat with the mower blades rotating, with the 
tractor in motion, or when the tractor engine is 
running. 
Always be alert for vehicle traffic when crossing 
or mowing near roadways. Avoid bystanders 
when mowing on or near public facilities. 

 

THE TRACTOR 

Always use an approved Roll Over Protective 
Structure (ROPS) and Seat Belt for safe 
operation. Overturning a tractor, without a 
ROPS, can result in serious injury or death. If 
your tractor is not equipped with a ROPS and 
Seat Belt, see your SHIBAURA Dealer. 
ALWAYS wear the seat belt on ROPS equipped 
tractors. DO NOT use a seat belt if the tractor 
ROPS has been removed. NEVER allow an 
open flame near the fuel tank or tractor battery.

 
 
 
 
 
 
 

WHEN YOU SEE THIS SYMBOL 

IT

 MEANS: 

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! 

Содержание MC60RD


































Отзывы: