Sharp XE-A307 Скачать руководство пользователя

Страница: 142 / 146

142

Before Calling for Service

If you encounter any of the following problems, please read below before calling for service.

Fault

Checking

• The display does not illuminate.

• Is power supplied to the electric outlet?
• Is the power cord plug out or loosely connected to

the electric outlet?

• Is the register in screen-save mode?

• The display is illuminated, but the whole machine

refuses entries.

• Is a clerk code assigned to the register?
• Is the register in the REG mode?

• No receipt is issued.

• Is the receipt paper roll properly installed?
• Is there a paper jam?
• Is the receipt function in the “OFF” status?
• Is the print roller arm securely locked?

• No journal paper is taken up.

• Is the take-up spool installed on the bearing

properly?

• Is there a paper jam?

• Printing is unusual.

• Are the printer head/sensor/roller clean?
• Is the paper roll properly installed?

Содержание XE-A307



















































































































































Результаты поиска

Содержание XE-A307

Отзывы:

Похожие инструкции для XE-A307

Бренды по названию

Популярные бренды

Sharp XE-A307, Инструкция по эксплуатации

Результаты поиска

Содержание XE-A307

Отзывы:

Похожие инструкции для XE-A307

Бренды по названию

Популярные бренды