Sharp XE-A307 страница 133 Скачать руководство пользователя | Manualshive

Страница: 133 / 146

background image

133

Installing Batteries

This register displays a low battery warning message “LOW BATTERY” when the batteries are low, and
displays a no battery warning message “NO BATTERY” when batteries are extremely low or batteries are
not installed.
If no batteries are installed, install two new alkaline batteries LR6 (“AA” size) at once. If batteries are already
installed, replace them with new ones as soon as possible. If the AC power cord is disconnected or a power
failure occurs when the batteries are dead or not installed, all the programmed settings will be reset to the
default settings and any data stored in memory will be cleared.

NOTE

Improper use of batteries could cause them to burst or leak, which might damage the interior of
the register. Please take the following precautions:

• Be sure that the positive (+) and negative (-) poles of each battery are oriented properly.
• Never mix batteries of different types.
• Never mix old batteries and new ones.
• Never leave dead batteries in the battery compartment.
• Remove the batteries if you plan not to use the register for long periods.
• Should a battery leak, clean out the battery compartment immediately, taking care not to let the

battery fluid come into direct contact with your skin.

• If an incorrect battery is used, it may explode or leak.
• For battery disposal, follow the relevant law or regulation in your country.

Replacement

1.

Be sure the register is plugged in.

2.

Remove the printer cover.

«
...
131
132
133
134
135
...
»

Содержание XE-A307



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для XE-A307

Бренд: Electro Industries/GaugeTech Страницы: 216

Бренд: Safescan Страницы: 16

Бренд: XIA Страницы: 76

Бренд: Parametric Страницы: 8

Бренд: Sam4s Страницы: 65

Бренд: Web Techniques Страницы: 12

Бренд: Regent Control Systems Страницы: 2

Бренд: LOVATO ELECTRIC Страницы: 13

Бренд: HEIDENHAIN Страницы: 18

Бренд: HEIDENHAIN Страницы: 25

Бренд: HEIDENHAIN Страницы: 40

Бренд: ELCOM Страницы: 68

Бренд: ELCOM Страницы: 84

Euro 500TE Handy

Бренд: ELCOM Страницы: 76

Бренд: ELCOM Страницы: 84

Бренд: ELCOM Страницы: 92

Бренд: ELCOM Страницы: 88

Бренд: ELCOM Страницы: 93

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды