Sharp UX-P100, Руководство по обслуживанию

Страница: 28 / 92

UX-P100U
UX-P200U
2 – 16
1S 1S
0.5S
RING
PATTERN 5
for CANADA
0.25S 0.25S
0.2S
6S
2S ring
4S ring
1.5S ring
3S ring
1S ring
4S ring
1.5S ring
4S ring
0.8S
4S ring
0.3S
4S ring
0.4S
4S ring
1S
4S ring
0.5S
0.5S
2S ring
2S ring
0.5S
0.5S
1S
0.2S
0.8S
0.4S
0.3S
0.2S
0.4S 0.8S
0.2S 0.2S
1S
1S
1S 0.5S
0.5S 0.5S
0.5S
1S
0.5S 0.5S
STANDARD
RING
PATTERN 1
for USA
RING
PATTERN 2
for USA
RING
PATTERN 3
for USA
RING
PATTERN 6
for CANADA
RING
PATTERN 7
for CANADA
RING
PATTERN 4
for USA
0.25S 0.25S 0.25S
0.2S 0.2S
RING
PATTERN 8
for CANADA
RING
PATTERN 9
for CANADA
SW-B6 No. 6 Dial tone detection (LCR center call) (UX-P100U ONLY)
Used to set YES/NO of dial tone detection (calling LCR center).
SW-B6 No. 7, No. 8 Reserved
Set to "0".
SW-C1 No. 1, No. 2 Reading slice (Binary)
Used to determine the set value of reading density in standard/fine mode.
The standard setting is "00" (Factory setting is "00")
SW-C1 No. 3, No. 4 Reading slice (Half tone)
Used to determine the set value of reading density in half tone mode.
The standard setting is "00" (Factory setting is "00")
SW-C1 No. 5 Line density selection
Used to set the transmission mode which is automatically selected when
the Resolution key is not pressed. In the copy mode, however, the fine
mode is automatically selected unless the Resolution key is manually
set to another mode.
SW-C1 No. 6 Reserved
Set to "0".
SW-C1 No. 7 MTF correction in half tone mode
This allows selection of MTF correction (dimness correction) in the half
tone mode.
When "NO" (=1) is selected, the whole image becomes soft and mild.
Clearness of characters will be reduced. Normally set to "YES" (=0).
SW-C1 No. 8 Reserved
Set to "0".
SW-D1 No. 1 ~ No. 4 Number of rings for auto receive
When the machine is set in the auto receive mode, the number of rings
before answering can be selected. It may be set from one to four rings
using a binary number. Since the facsimile telephone could be used as
an ordinary telephone if the handset is taken off the hook, it should be
programmed to the user’s choice. If the soft switch was set to 1, direct
connection is made to the facsimile. If a facsimile calling beep was heard
when the handset is taken off the hook, press the START key and put
the handset on the hook to have the facsimile start receiving. If it was
set to 0 accidentally, receive ring is set to 1.
NOTE: If the machine is set to answer after a large number of rings, it
may not be able to receive faxes successfully. If you have diffi-
culty receiving faxes, reduce the number of rings to a maximum
of 6.
SW-D1 No. 5 Automatic switching manual to auto receive mode
This soft switch is used to select whether the machine should switch to
the auto receive mode after 5 rings in the manual receive mode or re-
main in the same way as SW-D1 No. 1, No. 2, No. 3 and No. 4 "0"1"0"1"(5
rings).
SW-D1 No. 6 Reserved
Set to "0".
SW-D1 No. 7, No. 8 CI detect frequency
Detection frequency of ring signal for auto reception is set.
When set to No. 6=0, No. 7=0, frequency is set to PTT recommenda-
tion.
When set to No. 6=0, No. 7=1, frequency is set to 11.5Hz or more.
When set to No. 6=1, No. 7=0, frequency is set to 13.0Hz or more.
When set to No. 6=1, No. 7=1, frequency is set to 20.0Hz or more.
SW-D2 No. 1 ~ No. 3 Distinctive ringing setting (PATTERN 4 and 5
are for CANADA only)
This function allows reception of services offered by USA and Canada
telephone companies in which the customer contracts with the telephone
company to have up to 4 telephone numbers (USA) or 6 telephone num-
bers (Canada) established for one line.
Each telephone number is signalled by a different ringing pattern, and
the customer can allocate each number to a specific use.
Phone Number Intended Ring Pattern
Purpose
Ring Pattern 555-1234 Voice Calls Standard
555-1235 Facsimile Calls Pattern 1
555-1236 Answering Pattern 2
Machine
555-1237 PC Modem Pattern 3
<Distinctive Ringing Timing Specifications>
1) USA
DISTINCTIVE RING
→
1:RING PATTERN 1
→
2:RING PATTERN 2
↑ ↓
5:OFF SETTING
←
4:STANDARD RING
←
3:RING PATTERN 3
2) Canada
DISTINCTIVE RING
→
1:RING PATTERN 1
→
2:RING PATTERN 2
↑ ↓
7:OFF SETTING 3:RING PATTERN 3
↑ ↓
6:STANDARD RING
←
5:RING PATTERN 5
←
4:RING PATTERN 4
•
Ring Pattern
STANDARD has 5 ring patterns, and DISTINCTIVE has 9 patterns.
Ring patterns
1
~
4
for USA, and
5
~
9
for Canada.
However, to make the setting procedure as easy as possible for the
user to understand these patterns are grouped as follows:
<
Optional Setting>
1) RING PATTERN 1 RING PATTERN
1
for USA
RING PATTERN
4
for USA
RING PATTERN
5
for Canada
2) RING PATTERN 2 RING PATTERN
2
for USA
RING PATTERN
6
for Canada
3) RING PATTERN 3 RING PATTERN
3
for USA
RING PATTERN
7
for Canada
4) RING PATTERN 4 RING PATTERN
8
for Canada
5) RING PATTERN 5 RING PATTERN
9
for Canada
6) STANDARD RING
7) OFF SETTING
<Example of use>