Sharp UX-P100, Руководство по обслуживанию

Страница: 6 / 92

1 – 4
UX-P100U
UX-P200U
7. Use of Document Carrier Sheet
A document carrier sheet must be used for the following documents.
•
Those with tears.
•
Those smaller than size 5.8" (W) x 5.5" (L) (148mm (W) x 140mm
(L)).
•
Carbon-backed documents
NOTE: To transmit a carbon-backed document, insert a white sheet of
paper between the carbon back of the document and the docu-
ment carrier.
•
Those containing an easily separable writing substance (e.g., track-
ing paper written on with a soft, heavy lead pencil).
NOTES:
•
When using the document carrier, carefully read the in-
structions written on the back.
•
If the document carrier is dirty, clean it with a soft, moist
cloth, and then dry it before using for transmission.
•
Do not place more than one document in the carrier at a
time.
[4] Installation
1. Site selection
Take the following points into consideration when selecting a site for this
model.
ENVIRONMENT
•
The machine must be installed on a level surface.
•
Keep the machine away from air conditioners, heaters, direct sun-
light, and dust.
•
Provide easy access to the front, back, and sides of the machine. In
particular, keep the area in front of the machine clear, or the original
document may jam as it comes out after scanning.
•
The temperature should be between 41 - 95
°
F(5 - 35
°
C).
•
The humidity should be between 30% and 85% (without conden-
sation).
ELECTRICITY
AC 120V, 60Hz, grounded(3-prong) AC outlet is required.
Caution!
•
Connection to a power source other than that specified will cause
damage to the equipment and is not covered under the warranty.
•
If your area experiences a high incidence of lightning or power surges,
we recommend that you install a surge protector for the power and
telephone lines. Surge protectors can be purchased at most telephone
speciality stores.
If the machine is moved from a cold to a warm place...
Condensation may form on the reading glass if machine is moved from
a cold to a warm place, this will prevent proper scanning of documents
for transmission. Turn on the power and wait approximately 2 hours be-
fore using machine.
TELEPHONE JACK
A standard RJ11C single-line wall telephone jack must be located near
the machine. This is the telephone jack commonly used in most homes
and offices.
•
Plugging the fax machine into a jack which is not RJ11C single-line
wall telephone jack may result in damage to the machine or your
telephone system. If you do not know what kind of jack you have, or
need to have one installed, contact the telephone company.
2. Loading the Imaging Film (UX-5CR)
Your fax uses a roll of Imaging Film to create printed text and images.
The print head in the fax applies heat to the Imaging Film to transfer ink
to the paper. Follow the steps below to load or replace the film.
•
The initial starter roll of Imaging Film included with your fax can print
about 30 letter-size pages.(UX-P100U)
•
The initial starter roll of Imaging Film included with your fax can print
about 45 letter-size pages.(UX-P200U)
•
When replacing the film, use a roll of Sharp UX-5CR Imaging Film.
One roll can print about 150 letter-size pages.
Direction of insertion
Make print straight
across paper
E.G.
Place the document
carrier in the document
feeder with the clear film
side down
If you are loading the Imaging Film for the first time,
go to Step 4.
1
Remove the paper from the Paper Tray and open the Operation Panel
(press ).
Use only Sharp Genuine
Supplies with this logo:
2
Remove the used film and empty spool.
1
2
1
3
Remove the two green gears from the spools.
DO NOT DISCARD THE TWO GREEN GEARS!