Sharp MX-5111N Скачать руководство пользователя страница 62

Страница: 62 / 68

REPAIR HINTS

SHARP

DATA SECURITY KIT (Cont’d)

MX-FR33U

When printing to a specific folder

without PIN, Error 421 occurs - only

when DSK is installed.

To print to a specific folder without PIN, perform the

following setting changes:-

Settings - Security Settings - Other Settings -
Disabling of Document Filing menu:- Un tick Sharing
Mode for Printer.

User Control - Authority Group List - Add Authority
group Registration - Job Setting - Security -
Document Filing Approval Setting menu:- Enable
Sharing Mode.

EMAIL STATUS ALERTS

ALL

Is it possible to configure the MFP to

send only a single email alert for each

alert condition?

Upgrade the MFP firmware to February 2012 Running

Change (06.00.R1 or higher) and configure the

following soft switch:-

SIM 55-03 SW28-3 (change from 0 to 1).

Note:

For dealer email address, multiple email

notifications will still be received.

Configuring Toner Low Email alerts to

be sent at a specific toner remaining

level

If you wish to receive toner low emails at a specific

toner remaining level, configure the MFP as follows:-

1. Enter Simulation 26-69.

2. Change Item F (Toner E-Mail Alert) from 1 to 0.

3. Set Item B (Remaining Toner Level) to the specified

level when the Email alert is sent:-

Examples: 0= 5%, 1=10%, 2=15%, 3=20%, 4 = 25%

(Default), 5=30%.

Note: Depending on Model, the details within

Simulation 26-69 may differ therefore please refer to

the Service Manual for the relevant model series.

Содержание MX-5111N





































































Результаты поиска

Содержание MX-5111N

Отзывы:

Похожие инструкции для MX-5111N

Бренды по названию

Популярные бренды

Sharp MX-5111N, Техническое справочное руководство

Результаты поиска

Содержание MX-5111N

Отзывы:

Похожие инструкции для MX-5111N

Бренды по названию

Популярные бренды