Sharp MX-5111N Скачать руководство пользователя страница 58

Страница: 58 / 68

REPAIR HINTS

SHARP

TROUBLE INDICATIONS

All

Card Reader communication trouble.

This indication is displayed if a Card Reader is not

detected correctly when a Card Reader is registered on

the MFP.

Enter

User Control – Card Type/ Card Reader Settings

menu and uncheck

Use IC Card for Authentication

And/or de-register the Card Reader from

Card Reader

Device Registration

via the operation panel.

MX-EB12

HDD Trouble: Use SIM62-20 to check the HDD status.

For troubleshooting, refer to the MX-EB12 Mirroring Kit

section within this guide.

TROUBLE CODES

ALL

C4-20

Check if the Black drum cleaning blade has flipped.

Also check the condition of the primary transfer belt

unit.

E6-11 trouble after replacing the DSPF

Control PWB or DSPF CCD Unit.

DSPF Shading Adjustment (SIM63-2) must be executed

after replacing the DSPF CCD Unit, DSPF Control PWB

or following U2 trouble.

Use DSPF Shading Adjustment Sheet [UKOG-0333FCZZ],

MX-FX11

E7-07 error when sending or receiving

large volume of fax jobs

Upgrade the firmware to

04.00.R1

(or higher).

ALL

Intermittent E7-20

MX-EB11

E7-48

To support MX4111/5111N series and prevent E7-48

trouble, the MXEB11 firmware must be upgraded to

02.00.A1

(or higher).

ALL

E7-95

Check PCL Flash ROM , replace if required.

Also ensure to upgrade the Firmware to current version

MX-FNX9

F1-00 trouble after a firmware

upgrade

When performing a firmware upgrade on the Inner

Finisher, ensure to select both BOOT & MAIN firmware

after executing Sim 49-01.

Due to a recent change, both BOOT & MAIN firmware

versions have been upgraded however, if only the

MAIN firmware is selected and upgraded, F1-00 trouble

may be experienced when using the combination of

original BOOT and current MAIN firmware versions.

MX-FN10

F1-08

Upgrade the MXFN10 Firmware to v01.10.02 (or

higher) for improved Gripper control

Ensure "Super Lube" Synthetic Multi-Purpose Grease

(SUP21030) is applied to the square shaft within the

staple unit otherwise, the gripper drive gear (PG:

Section 24 item 11 -

0CW4158P418//

) may wear

prematurely, causing it to bind under load.

ALL

U5-16 trouble (DSPF cooling fan

permanently runs)

Replace the DSPF Driver PWB (

CPWBN1982FCE1

ALL

Constant Error 1206 when adding an

address destination - even after

resetting system settings back to

factory default.

Check the HDD operation for bad or corrupted

partition. Execute Sim 62-01 and format the HDD.

If the problem persists after formatting, replace the

HDD unit.

Содержание MX-5111N





































































Результаты поиска

Содержание MX-5111N

Отзывы:

Похожие инструкции для MX-5111N

Бренды по названию

Популярные бренды

Sharp MX-5111N, Техническое справочное руководство

Результаты поиска

Содержание MX-5111N

Отзывы:

Похожие инструкции для MX-5111N

Бренды по названию

Популярные бренды