Sharp MX-5111N Скачать руководство пользователя страница 13

Страница: 13 / 68

SHARP

MAINTENANCE

Maintenance Indications:

Black Drum (Counter) has reached

the specified life.

Replace Black Drum

Process

Section

(Drum)

Cyan Drum (Counter) has reached

the specified life.

Replace Cyan Drum

Magenta Drum (Counter) has reached

the specified life.

Replace Magenta Drum.

Yellow Drum (Counter) has reached

the specified life.

Replace Yellow Drum.

Black Developer (Counter) has reached

the specified life.

Replace Black Developer.

Process

Section

(Developer)

Cyan Developer (Counter) has reached

the specified life.

Replace Colour

Developer Kit.

Magenta Developer (Counter) has reached

the specified life.

Yellow Developer (Counter) has reached

the specified life.

FK1

Fusing Belt Print Counter has reached the

specified limit.

Replace the Fusing

Belt Kit.

Fuser

Section

FK2

Fuser Pressure Roller Print Counter has

reached the specified limit.

Replace the Pressure

Roller Kit.

FK3

Fuser Web Cleaner (Counter) has reached

the specified limit

(Pop Up FK3 Error – Web End Detected)

Replace the

Web Cleaning Kit

TK1

Primary Transfer Unit Counter has reached

the specified limit.

Replace Primary Transfer

Belt and Blade kits.

Transfer

Section

TK2

Secondary Transfer Unit Counter has

reached the specified limit.

Replace the Secondary

Transfer Belt Kit.

Maintenance [All] Counter has reached specified limit

Maintenance [Colour] Counter has reached specified limit

Maintenance [All] & [Colour] Counters have reached the specified limits

Starting Powder:

The following starting powder should be applied to the relevant consumable item during maintenance:-

Starting Powder

OPC Drum

Primary Transfer Belt

MX-4111N
MX-5111N

UKOG-0312FCZZ

[Stearic Acid]

CKOG-0345DS51 *

[Yellow Toner]

Note*:

Kynar Powder [UKOG-0123FCZZ] can also be applied to the Primary Transfer Belt.

CAUTION:

Do not apply Stearic Acid (UKOG-0312FCZZ), Strontium Titanium (UKOG-0316FCZZ) or Titanium
Hydroxide (UKOG-0322FCZZ) starting powder to the Primary Transfer Belt.

Содержание MX-5111N





































































Результаты поиска

Содержание MX-5111N

Отзывы:

Похожие инструкции для MX-5111N

Бренды по названию

Популярные бренды

Sharp MX-5111N, Техническое справочное руководство

Результаты поиска

Содержание MX-5111N

Отзывы:

Похожие инструкции для MX-5111N

Бренды по названию

Популярные бренды