Sharp MX-5111N Скачать руководство пользователя страница 8

Страница: 8 / 68

INITIAL SETUP

SHARP

DEVELOPER SET-UP

Sim 25-02

Auto Developer Adjustment -

Select CMYK.

Toner Installation must be performed after Auto Developer Adjustment is
completed.

**For optimum image quality & performance, it is recommended to setup &
install developer at the customer site.

Clean LSU Dust Proof Glass.

TONER INSTALLATION & REPLENISHMENT

Install CMYK Toner Cartridges.

Caution:

DO NOT open any Exterior Cover, Power OFF/ON or enter Simulation Mode
during Initial Toner Replenishment.

PRODUCT ACTIVATION & FIRMWARE UPGRADE

Activation of Optional Product(s):-

System Settings – Product Key.

Sim 22-05

Check Firmware version(s):-

Upgrade to latest version.

INITIAL SETUP

Sim 26-01

Right Tray Installation:-

Yes/No.

Sim 26-02

LCC Installation (Paper Size):-

A4.

Sim 26-06

Machine Destination.

Sim 26-35

Set Multi Error Counter:-

Set to 1 (Multi Count).

Sim 26-50

Long Paper Support (up to 1200mm):-

0 = Disable, 1 = Enable.

Sim 26-52

Non Printed Paper Counter Set-up.

Sim 55-03

Process Mixed Size Pages (orientation) when Printing in Duplex:-
SSW 3-6,

0 = Disable, 1 = Enable.

Sim 55-03

Toner Remain Status Display: SSW 22-5,

0 = Disable, 1 = Enable.

System Settings:

Adjust Date/Time (Inc. Daylight Saving setting).

Keyboard Language Setting (For Embedded & Optional Keyboards):

System Settings – Default Settings – Keyboard Select: Set English(US)

Network Settings – Print Port Settings:

Disable WSD.

Set cassette size by adjusting the guides in the cassette.

Paper Size & Type Setting

System Settings – Paper Tray Settings.

Содержание MX-5111N





































































Результаты поиска

Содержание MX-5111N

Отзывы:

Похожие инструкции для MX-5111N

Бренды по названию

Популярные бренды

Sharp MX-5111N, Техническое справочное руководство

Результаты поиска

Содержание MX-5111N

Отзывы:

Похожие инструкции для MX-5111N

Бренды по названию

Популярные бренды