background image

SHARP

 

SD CARD REPLACEMENT PROCEDURE

 

 

 

39 

 

 

Replacement Procedure: 

 

When replacing the SD card, be sure to use the specified SD card supplied as a service part only. 

The firmware required for booting the MFP device must be included on the SD card that is used in 
this machine - Commercially available SD cards do not have this firmware data.

 

 

1.

 

Use SIM56-02 to backup the SD card data to the USB memory. 

2.

 

When the operation panel home screen has been customised, backup the SD card data by using 
the device cloning function. 

3.

 

When there is FAX/Internet Fax data received, use SIM66-62 to backup the image data to the USB 
memory (PDF file type), and then provide the PDF data to the user. (The data cannot be restored to 
the machine.) 

4.

 

Replace the SD card with a new one. 

5.

 

Upgrade the firmware to the latest version. 

6.

 

Use  SIM66-10 to  clear  the  image  send  memory. (This  is  in order  to  obtain  consistency between 
the  HDD  data  and  the image related memory.) 

7.

 

Use SIM56-02 to restore the data backed up in procedure 1. 

8.

 

Restore  the  data  backed  up  in  procedure  2  by  using  the device cloning function. 

 

Notes: 

 

 

If E7-07 or U2-40 trouble occurs and the error cannot be cancelled using SIM16, this may 
indicate an issue or failure of the SD Card – replace the SD Card by following the procedure 
detailed above. 

 

 

The data backed up with SIM56-2 must not be installed to another machine. If installed, the 
system and adjustment data will be overwritten and other issues may be generated. 

 
 
 
 
 

Содержание MX-5111N





































































Отзывы: