Sharp MX-2640N страница 65 Скачать руководство пользователя

Страница: 65 / 71

SHARP

REPAIR HINTS

SPECIFICATION

Model

Symptom

Advice

ALL

Is it possible to Tandem

MX-2640/3640N series with another

MX colour device?

Tandem operation is only supported with

MX-2640/3140/3640N series only.

Is it possible to retain the Destination

Address (Image Send Mode), once the

current Scan operation is complete?

To enable this function, change,

SIM55-03 SW30-3 from 0 (default) to 1.

Once enabled, go to System Settings-Image Send

Settings-Operation Settings menu and enable the “Hold

Address for a while after scanning is completed” option

for the relevant Image Send mode.

TROUBLE CODES

ALL

C4-00

To prevent static discharge (change of bias voltages),

upgrade the PCU firmware to 04.04.G2.00 (or higher).

Also check the operation of the Drum Phase sensors

and the clutches that change the position of the

Primary Transfer Belt . The belt may not be locking

securely into the colour or BW position.

PG Section 51, item 20 (x2). PCLC-0373FCZ1

U2-00

The latest Running Change firmware now supports

U2-00 cancellation therefore:-

1. Upgrade the MFP Firmware to 03.00.A2 (or higher).

2. Clear U2-00 trouble by executing SIM16.

MX-EB11

E7-47 trouble

To support MX-2640/3140/3640N series, the ACU

firmware version must be upgraded to 01.00.A2.

Use SIM49-10 to perform the ACRE firmware upgrade.

GENERAL / MISC

ALL

Error K, C, M, Y in Sim44-26 and/or

machine hangs in Sim46-74 when

trying to print the calibration sheet.

Check/replace CF card on the MFP PWB.

MFP fails to boot (or keeps rebooting)

Please ensure the CF Card is installed correctly.

Make sure it is seated all the way and "clicks" into

place.

No Output Tray Is Allowed error

message

The above message can be displayed if the machine

power is turned OFF just before the lift up of Tray 3 or

4 is completed.

To work around this issue, open & close Tray 3 or 4

when the message appears or upgrade the PCU

firmware to 04.01.G1 (or higher).

MX-DE13
MX-DE14

The MXDE13 or MXDE14 desk unit is

not recognised correctly (1 or 2

drawers missing from the

configuration) after installation.

To support future models, the Transfer Motor SB

installed on the MXDE13 & MXDE14 desk unit has been

changed since June 2013 production therefore, when

the current desk unit is installed onto an earlier

machine for example, both PCU & Desk firmware must

be upgraded to the latest version to ensure

compatibility.

Содержание MX-2640N








































































Результаты поиска

Содержание MX-2640N

Отзывы:

Похожие инструкции для MX-2640N

Бренды по названию

Популярные бренды

Sharp MX-2640N, Техническое руководство

Результаты поиска

Содержание MX-2640N

Отзывы:

Похожие инструкции для MX-2640N

Бренды по названию

Популярные бренды