background image

SGM

 

 

GB

 

 

XM473-V1.0-NR 

 

Idea  Spot  700 

 

SAFETY INSTRUCTIONS 

CAUTION

 

 

 

Be careful with your operations. With a dangerous voltage you can Suffer a 
dangerous electric shock when touching wires!

 

 
This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe 
operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written 
in this user manual. 
 

IMPORTANT 

Damages caused by the disgregard of this user manual are not subject to warrenty. 

The dealer will not accept liability for any resulting defects or problems.

 

 
If the device has been exposed to temperature changes due to environmental changes, do not switch it on 
immediately. The arising condensation could damage the device. Leave the device switched off until it has 
reached room temperature. 
 
This device falls under protection-class I. Therefore it is essential that the device be earthed. 
The electric connection must carry out by qualified person. 
 
The device shall only be used with rate voltage and frequency.

 

Make sure that the available voltage is not higher than stated at the end of this manual. 
 
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, 
replacement of the cable must be done by an authorized dealer. 
 
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the 
power cord by the plug. Never pull out the plug by tugging the power cord. 
 
During initial start-up some smoke or smell may arise. This is a normal process and does not necessarily 
mean that the device is defective, it should decrease gradually. 
 
Please don't project the beam onto combustible substances. 
 
Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for 
smooth air flow, so there should be no shelter for fans and ventilation for heat radiation. 
 
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the 
manufacturer or his service agent or a similar qualified person in order to avoid a hazard. 
 

CAUTION 

 

Never touch device during operation! 
The housing may heat up.

 

 

Never look directly into the light source,   
as sensitive persons may suffer an epileptic shock.

 

 
Please be aware that damages caused by manual modifications to the device are not subject to warranty. 
Keep away from children and non-professionals. 
 

Содержание IDEA SPOT 700































Отзывы: