SGM IDEA SPOT 700, Руководство пользователя

Страница: 12 / 30

SGM
GB
XM473-V1.0-NR Idea Spot 700
１０
Operting instructions of the internal DMX wireless system
1. Equipments:
DMX 512 controller, wireless transmitter, and the fixtures with wireless receiver.
2. Message from the LED indicator:
1. Rapid flashing red/Green: logging in to a transmitter
2. Slow flashing Red/Green: Logged on a transmitter and the DMX line is idle (No DMX is connected
to transmitter).
3. Solid Green: Logged on to a transmitter and receiving DMX data.
4. Solid Red: Not logged on to a transmitter (free)
3. DMX in the menu of the fixture:
On a fixture installed with wireless system, in order to switch between wireless control system and
traditional DMX control (with cable), a new menu WDMX is added to the display board.
ON: (Activate WDMX)
1. When the fixture is on power
，
and the WDMX is activated to ON status, but did not connect to the
controller and did not log in to the transmitter, the fixture will search for the DMX signal source. If
the fixture is connected to the DMX controller it can be controlled by DMX controller; if it is log in
to the wireless transmitter, it can be controlled by the Transmitter
2. When the fixture is power off, and the WDMX is in ON status, if the fixture is connected to DMX
controller. After the fixture is power on, it can be controlled only by the DMX controller which
connected. The fixture can log in the wireless transmitter, and receive only radio signal from
transmitter, but not DMX from the transmitter.
OFF
: (De-activate WDMX)
In this status, wireless system is not activated, so the fixture can not log in the transmitter.
REST
: (reset WDMX memory);
Can remove the fixture from the connection with the transmitter, the fixture become free and ready
to log in any transmitter.
OUT
:
（
Act & Data Out
）
4. Setup the wireless system:
1. Connect the transmitter with the DMX controller
2. To make the fixture installed with wireless receiver log in to the transmitter
a) Initially, the indicator on the receiver fixture should be in Solid red
b) Press and hold the configuration button on transmitter for less than 3 seconds the red/green
LEDs on the transmitter and the receiver fixture will flash rapidly for about 5~ 10 seconds while
the system goes through its setup procedure.
c) Once the receiver fixture is logged in to the transmitter (T1), the fixture with wireless receiver
will keep the memory, even if restart the power, this unit will log in the transmitter (T1)
automatically.
3. Use the DMX 512 to control the fixture
5. Remove the receivers from transmitter (T1) and to log in to another transmitter (T2)
Case 1 : Remove a receiver:
a) On the control board of the fixture, enter menu to activated the function of REST;
b) The LED for wireless on the fixture should turn to Solid red; the receiver can log out from the
transmitter (T1);
c) press the configuration button on transmitter(T2) for less than 3 second, then the fixture will start
to connect with the transmitter(T2)
Case 2 : Remove all receivers from a transmitter (T1) to log in to T2;
a) Press and hold the configuration button on the T1 as least 5 seconds, can clear the connection with
all the fixtures.
b) All the red/green LEDs on the receiver fixtures will turn to Solid red to indicate that the receivers
are unassigned and removed from the transmitter ( T1);
c) Press and hold the configuration button on the T2 less then less than 3 second , the fixtures will
connect with the T2
PS:
1.
Please log the receivers out from the transmitter after every job, so that the receivers are in free un
assigned state and ready to be assigned to a transmitter.
2. Do not connect the fixture which is under the communication of wireless system to the DMX controller,
otherwise it will cause interference from the DMX controller.