Industry Canada NOTICE
Notice:
The Industry Canada label identifies certified equipment.
This certification means that the equipment meets certain
telecommunications network protective, operational and safety
requirements. Industry Canada does not guarantee the equipment
will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed
using an acceptable method of connection. The customer should
be aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated by the supplier. Any
repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment.
User should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
Caution:
Users should not attempt to make such connections
themselves, but should contact the appropriate electric inspection
authority, or electrician, as appropriate.
NOTICE:
The Load Number assigned to each terminal device denotes
the percentage of the total load to be connected to a telephone
loop which is used by teh device, to prevent overloading. The
termination on an interface may consist of any combination of
devices subject only to the requirement that the total of the Load
Numbers of all the devices does not exceed 100.
The Load Number of this unit is 40.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communication. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
CAUTION:
Changes or modification not expressly approved by Sur-
Gard Security Systems Ltd. could void the user’s authority to operate the
equipment.
Important Information
This equipment complies with Part 68 of the FCC Rules. On the back
of this equipment is a label that contains among other information, the
FCC registration number of this equipment.
Notification to Telephone Company
Upon request, the customer shall notify the telephone company of the
particular line to which the connection will be made, and provide the
FCC registration number and the ringer equivalence of the protective
circuit.
FCC Registration Number:
1VDCAN-74582-AL-N
Ringer Equivalence Number:
0.3B
Telephone Connection Requirements
Except for the telephone company provided ringers, all connections to
the telephone network shall be made through standard plugs and telephone
company provided jacks, or equivalent, in such a manner as to allow for
easy, immediate disconnection of the terminal equipment. Standard jacks
shall be so arranged that, if the plug connected thereto is withdrawn, no
interference to the operation of the equipment at the customer’s premises
which remains connected to the telephone network shall occur by reason
of such withdrawal.
AVIS:
L’étiquette de l’Industrie Canada identifie le matériel
homologué. Cette étiquette certifie que le matériel est conforme à
certaines normes de protection, d’exploitation et de sécurité des
réseaux de télécommunications. Industrie Canada n’assure toutefois
pas que le matériel fonctionnera à la satisfaction de l’utilisateur.
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est
permis de le raccorder aux installations de l’entreprise locale de
télécommunication. Le matériel doit également être installé en suivant
une méthode acceptée de raccordement. L’abonné ne doit pas
oublier qu’il est possible que la conformité aux conditions énoncées
ci-dessus n’empêchent pas la dégradation du service dans certaines
situations.
Les réparations de matériel homologué doivent être effectuées par
un centre d’entretien canadien autorisé désigné par le fournisseur.
La compagnie de télécommunications peut demander à l’utilisateur
de débrancher un appareil à la suite de réparations ou de
modifications effectuées par l’utilisateur ou à cause de mauvais
fonctionnement.
Pour sa propre protection, l’utilisateur doit s’assurer que tous les
fils de mise à la terre de la source d’énergie électrique, les lignes
téléphoniques et les canalisations d’eau métalliques, s’il y en a,
sont raccordés ensemble. Cette précaution est particulièrement
importante dans les régions rurales.
AVERTISSEMENT:
L’utilisateur ne doit pas tenter de faire ces
raccordements lui-même; il doit avoir recours à un service d’inspection
des installations électriques, ou à un électricien, selon le cas.
L’indice de charge (IC) assigné à chaque dispositif terminal indique,
pour éviter toute surcharge, le pourcentage de la charge totale qui
peut être reccordée à un circuit té;éphonique bouclé utilisé par ce
dispositif. La terminaison deu circuit bouclé peut être constituée de
n’importe quelle combinaison de dispositifs, pourvu que la somme des
indices de charge de l’ensemble des dispositifs ne dépasse pas 100.
L’indice de charge de ce produit est 40.
Incidence of Harm
Should terminal equipment or protective circuitry cause harm to the telephone
network, the telephone company shall, where practicable, notify the customer
that temporary disconnection of service may be required; however, where
prior notice is not practicable, the telephone company may temporarily
discontinue service if such action is deemed reasonable in the circumstances.
In the case of such temporary discontinuance, the telephone company
shall promptly notify the customer and will be given the opportunity to
correct the situation.
Changes in Telephone Company Equipment or Facilities
The telephone company may make changes in its communications facilities,
equipment, operations or procedures, where such actions are reasonably
required and proper in its business. Should any such changes render the
customer’s terminal equipment incompatible with the telephone company
facilities, the customer shall be given adequate notice to effect the
modifications to maintain uninterrupted service.
General
This equipment should not be used on coin telephone lines. Connection
to party line service is subject to state tariffs.
Ringer Equivalence Number (REN)
The REN is useful to determine the quantity of devices that you may
connect to your telephone line and still have all of those devices ring
when your telephone number is called. In most, but not all areas, the sum
of the REN’s of all devices connected to one line should not exceed five
(5). To be certain of the number of devices that you may connect to your
line, you may want to contact your local telephone company.
Equipment Maintenance Facility
If you experience trouble with this telephone equipment, please contact
the facility indicated below for information on obtaining service or repairs.
The telephone company may ask you disconnect this equipment from the
network until the problem has been corrected or until you are sure that
the equipment is not malfunctioning.
U.S. Point of Contact
Digital Security Controls Ltd.
160 Washburn St.
Lockport, NY 14094
