SEW movifit mc Скачать руководство пользователя страница 142

Страница: 142 / 184

Operation

MOVIFIT® MC status LEDs

Operating Instructions – MOVIFIT

142

"F-STATE" LED

The following table shows the statuses of the "F-STATE" LED:

LED

Meaning

Measure

Off

The S12 safety option is currently in the
initialization phase.

S12 safety option is not available.

Verification is not completed (by switch-
off/on or by bus startup)

• Check configuration of bus

master.

• Switch the unit off/on.

Yellow

Illuminated

S12 safety option is in RUN mode, but
safety parameters not verified yet.

• Perform verification of

safety parameters.

Yellow

Flashing

Flash code for identification of the de-
vice during authentication (entering the
serial number in "Assist S12")

Green

Illuminated

S12 safety option is in RUN mode, veri-
fication of safety parameters completed.

Yellow/
green

Flashing

Test mode for drive safety functions is
active.

Red

Flashing

Error occurred
(error can be acknowledged).

• Error diagnostics.
• Correct the error and ac-

knowledge via F host or
programmed F-DI input.

Red

Illuminated

An error has occurred.
(Error cannot be acknowledged)

No 24 V_0 supply voltage

• Error diagnostics
• Check voltage supply.

19484828/EN – 01/2015

Содержание movifit mc

























































































































































































Результаты поиска

Содержание movifit mc

Отзывы:

Бренды по названию

Популярные бренды

SEW movifit mc, Руководство по эксплуатации

Результаты поиска

Содержание movifit mc

Отзывы:

Бренды по названию

Популярные бренды