SEW-Eurodrive MOVI-C UHX45A Series Скачать руководство пользователя страница 68

Страница: 68 / 92

Startup with PROFINET IO

Configuration of the fieldbus stations

Manual – MOVI-C

CONTROLLER advanced with PROFINET IO Fieldbus Interface

6. Select the PROFINET device name of the MOVI‑C

CONTROLLER.

22807324043

7. Set the used programming interface of the MOVI‑C

CONTROLLER and refresh

the list of stations.

8. Select the MOVI‑C

CONTROLLER and assign a device name. This overwrites

the suggested name of the device description file (GSDML file).

If the PROFINET device name has been assigned successfully,
MOVI‑C

CONTROLLER sends the status "OK". The status LED BF goes out.

9. Save the TIA Portal project.

5.4.6

Loading the MOVISUITE

project to the MOVI-C

CONTROLLER

The fieldbus interface for the slave connection has to be set in the MOVISUITE

pro-

ject and the device configuration has to be loaded to the MOVI‑C

CONTROLLER via

the IEC Editor.

Proceed as follows:

You integrated the MOVI-C

devices into a MOVISUITE

project.

1. Switch to the MOVISUITE

project.

24777730/EN – 01/2018

Содержание MOVI-C UHX45A Series





























































































Результаты поиска

Содержание MOVI-C UHX45A Series

Отзывы:

Бренды по названию

Популярные бренды

SEW-Eurodrive MOVI-C UHX45A Series, Руководство пользователя

Результаты поиска

Содержание MOVI-C UHX45A Series

Отзывы:

Бренды по названию

Популярные бренды