SEW-Eurodrive MOVI-C UHX45A Series Скачать руководство пользователя страница 62

Страница: 62 / 92

Startup with PROFINET IO

Configuration of the fieldbus stations

Manual – MOVI-C

CONTROLLER advanced with PROFINET IO Fieldbus Interface

In this example, the MOVI‑C

CONTROLLER in the UHX45A-N device variant

is used and assigned to the controller with the device name "PLC".

5. To configure the MOVI‑C

CONTROLLER, double-click on the device.

The device view is displayed.

6. Enter the same name for the MOVI‑C

CONTROLLER in the inspector window

(lower editor section) in the "General" tab as in the MOVISUITE

project. The

device is shown in the TIA Portal project under this name.

22807268875

The MOVI‑C

CONTROLLER has the following project name in this example:

CONTROLLERUHX45A

24777730/EN – 01/2018

Содержание MOVI-C UHX45A Series





























































































Результаты поиска

Содержание MOVI-C UHX45A Series

Отзывы:

Бренды по названию

Популярные бренды

SEW-Eurodrive MOVI-C UHX45A Series, Руководство пользователя

Результаты поиска

Содержание MOVI-C UHX45A Series

Отзывы:

Бренды по названию

Популярные бренды